Challenger MR6 6,000 lb. Portable Mid-Rise Lift
$3,699.00
Challenger’s midrise lift is a great way to increase the productivity of any shop. We mounted the motor to a heavy-duty tow dolly, making it portable and able to operate on concrete, indoors, or out. Save valuable shop space while servicing brakes, tires or detailing a vehicle’s exterior. The 6,000
The Challenger MR6 is a 6,000 lb. portable mid-rise lift that raises vehicles to 52.75 inches in about 45 seconds. With sliding and rotating arms, short and tall auxiliary adapters, six lock positions, and a motor mounted on a heavy-duty tow dolly, the Challenger MR6 brings flexible, productive lifting to shops and garages.
Includes auxiliary adapters to reach a more comprehensive range of vehicle lift points. Exclusive features include a sliding/rotating arm design with rubber pads, low drive-over clearance, and more.
- 6,000 lb. lift capacity
- 52.75” raised height
- 40” overall width
- Short and tall auxiliary adapters come standard to reach pickup points on a wider range of vehicles
- Multiple locking positions accommodates higher profile vehicles and provides maximum headroom to work underneath vehicles
- Powder coated finish provides long-lasting durable finish
| Model Number | MR6 |
|---|---|
| Lifting Capacity | 6,000 lbs. |
| Rise Height | 52.75” |
| Overall Length | 94” |
| Overall Width | 40” |
| Min. Collapsed Table Height | 5.5” |
| Pad Height (Min.) | 8.625” |
| Pad Height (Max.) | 60” |
| Hydraulic Hose | 144” |
| Safety Lock Positions | 6 |
| Motor / Voltage | 1HP, 115V, 60Hz, 1Ph |
| Speed of Rise | 45 s |
| Min. Recomm. Bay Size | 10′ x 22′ |
| Colors Available | Black |
Challenger MR6 Specifications
- Lifting capacity: 6,000 lbs.
- Rise height: 52.75 inches
- Overall length: 94 inches; overall width: 40 inches
- Minimum collapsed table height: 5.5 inches
- Pad height: 8.625 inches minimum, 60 inches maximum
- Hydraulic hose length: 144 inches
- Safety lock positions: 6
- Motor: 1 HP, 115V, 60Hz, single phase
- Speed of rise: about 45 seconds
- Minimum recommended bay size: 10 ft. x 22 ft.
- Finish: black powder coat
What Makes the Challenger MR6 Stand Out
Many mid-rise lifts use fixed platforms. The Challenger MR6 uses a sliding and rotating arm design with rubber pads, so you can position each pad right at the vehicle’s lift point. Short and tall auxiliary adapters come standard, helping you reach pickup points on a wider range of vehicles, from small passenger cars to light trucks.
At 52.75 inches, the Challenger MR6 lifts higher than many mid-rise lifts, giving you more room to work underneath while still keeping the low, compact footprint that makes a mid-rise lift so practical.
Portable by Design
Challenger mounted the motor on a heavy-duty tow dolly, making the Challenger MR6 portable. It can operate on concrete indoors or outdoors, so you can bring it to the job instead of bringing every job to one bay. The 144-inch hydraulic hose gives you plenty of reach between the power unit and the lift. When you’re done, move it aside and reclaim your floor space.
Six Lock Positions
The Challenger MR6 has six safety lock positions. Multiple positions let you lock the vehicle at the height that suits the job, whether you’re working on wheels at waist level or need maximum headroom underneath. They also help when lifting higher-profile vehicles.
Low Drive-Over Clearance
With a minimum collapsed table height of 5.5 inches, the Challenger MR6 lets many vehicles drive over it. Position the lift, drive the vehicle into place, adjust the arms, and lift. The low profile speeds up every job and makes the lift easy to use with a wide range of cars.
Durable Powder-Coated Finish
A tough black powder-coated finish protects the Challenger MR6 against chips, scratches, and corrosion. It’s built to look good and hold up to daily shop use for years.

Who Should Buy the Challenger MR6
- Tire and brake shops that need fast, flexible lifting
- Detail shops working on exteriors and lower panels
- General repair shops looking to add capacity without a new bay
- Home garages with room for a 10 ft. x 22 ft. work area
- Mobile operations that need a lift indoors and outdoors
- Shops servicing everything from small cars to light trucks
Compare more options in our portable car lifts category.
How to Use the Challenger MR6
- Tow the lift into position on level concrete using the dolly.
- Connect the hydraulic hose and plug the 115V motor into a suitable outlet.
- Drive the vehicle over the collapsed lift.
- Slide and rotate the arms so each rubber pad sits under a lift point.
- Add short or tall auxiliary adapters if the lift points are higher.
- Raise a few inches and check every pad.
- Raise to the desired height and lower onto the nearest lock position.
Safety Guidelines
Never exceed the Challenger MR6’s 6,000 lb. capacity. Always use manufacturer-approved lift points and confirm each pad is secure before lifting higher. Lower the vehicle onto a lock position before working beneath it. Keep everyone clear while lifting and lowering, and follow the Challenger operating manual at all times.
Best Jobs for the Challenger MR6
- Brake pads, rotors, and calipers
- Tire changes and wheel service
- Detailing and paint correction
- Suspension inspections and repairs
- Oil changes and fluid service
- Pre-delivery inspections
Space and Power Requirements
Challenger recommends a minimum bay size of 10 ft. x 22 ft. for the Challenger MR6. You’ll also need a level concrete floor and a 115V outlet for the 1 HP motor. Because it’s a mid-rise lift, it doesn’t need a tall ceiling, which makes it a strong option for spaces where a two-post lift won’t fit.
Maintenance Tips
- Inspect the hydraulic hose and fittings for leaks or damage.
- Check the hydraulic fluid level in the power unit.
- Keep the lock mechanism clean and working freely.
- Inspect the rubber pads and auxiliary adapters for wear.
- Lubricate pivot points as recommended in the manual.

Challenger MR6 vs. a Two-Post Lift
A two-post lift raises vehicles high enough to stand underneath, but it needs a tall ceiling, a thick slab, and a permanent install. The Challenger MR6 needs no tall ceiling, can be moved, and lifts to 52.75 inches, which is ideal for wheel, brake, and detailing work. Many shops pair a mid-rise lift with their two-post lifts to speed up quick jobs.
Challenger MR6 vs. Low-Rise Lifts
Low-rise lifts are compact but usually lift only about two feet. The Challenger MR6 goes more than twice as high, so technicians can work more comfortably, and with six lock positions you can choose the height that fits each job.
Why Sliding and Rotating Arms Matter
Vehicles come in many shapes and sizes, and their lift points aren’t always in the same place. Fixed-platform lifts can force you to compromise on pad position. The Challenger MR6 solves that with arms that slide and rotate. You can move each rubber pad right under the manufacturer’s lift point, then add short or tall auxiliary adapters to match the height. Precise placement means a more stable lift and less risk to the vehicle’s body and underbody components.
Boosting Shop Productivity
Challenger designed the Challenger MR6 to increase shop productivity. A lift that rises in about 45 seconds, locks at multiple heights, and moves where it’s needed helps your technicians work faster. Wheels and brakes are easy to reach, detailers can work on lower panels without kneeling, and inspectors can see the underbody clearly. Adding a portable mid-rise lift is one of the most cost-effective ways to increase capacity in a busy shop.
Indoor and Outdoor Use
Because the motor is mounted on a tow dolly and the lift operates on concrete indoors or out, the Challenger MR6 is well suited to businesses that work outside their main building. Detail shops can use it on a covered pad, dealerships can use it on the prep line, and fleet operators can bring it to where vehicles are parked. Always make sure the surface is level, solid concrete before lifting.
Using the Auxiliary Adapters
The Challenger MR6 comes standard with short and tall auxiliary adapters. Short adapters help with vehicles whose lift points sit slightly higher than the pads. Tall adapters are useful for light trucks and SUVs with more ground clearance. With pad heights ranging from 8.625 inches to 60 inches, the lift can match a wide range of vehicles.

A Typical Brake Job
Drive the vehicle over the collapsed Challenger MR6. Slide and rotate the arms to the lift points, add adapters if needed, and raise the vehicle a few inches to check pad contact. Continue to a comfortable working height and lower onto a lock. Pull the wheels, service the brakes on all four corners, and reinstall. Release the locks, lower the vehicle, and drive it off. The whole process is quick and comfortable, which helps keep your bays moving.
A Typical Detailing Session
Detailers can raise a vehicle to a height where the rocker panels, lower doors, bumpers, and wheel wells are easy to reach. That makes washing, polishing, coating, and protection film installation more precise and less tiring. With six lock positions, you can choose exactly the height that works best for each task.
Planning Your Bay
Before your Challenger MR6 arrives, measure your space. Challenger recommends at least 10 ft. x 22 ft. for the lift and vehicle. Check that the floor is level concrete without large cracks, and confirm you have a 115V outlet within reach of the 144-inch hose and the dolly-mounted motor. Plan where the lift will be stored when not in use, and make sure there’s a clear path to tow it there.
Training Your Team
Every technician who uses the Challenger MR6 should read the operating manual and understand lift point placement, the use of adapters, and the lock positions. Post safety instructions near the lift and review them regularly. Consistent training keeps your team safe and helps them get the most out of the lift.
Built for Daily Use
From its powder-coated finish to its heavy-duty tow dolly, the Challenger MR6 is built for the demands of daily shop use. With routine inspections and basic maintenance, it will provide years of reliable service. Learn more about the manufacturer on the official Challenger Lifts website.
Vehicles That Fit the Challenger MR6
With a 6,000 lb. capacity, adjustable arms, and short and tall adapters, the Challenger MR6 can lift vehicles from small passenger cars to light trucks. That includes compact cars, sedans, coupes, crossovers, many SUVs, and many light pickups. The low 5.5-inch collapsed height helps lower vehicles drive over the lift, and the 8.625 to 60 inch pad height range covers a wide variety of lift point heights. Always confirm vehicle weight and lift points before lifting.

Comfort for Technicians
Working on wheels, brakes, and lower panels all day takes a toll when the vehicle sits on the ground or only a couple of feet up. The Challenger MR6 lets technicians choose a working height that suits them and the task. Less bending and kneeling means less fatigue, better focus, and fewer mistakes. Over weeks and months, that comfort has a real effect on productivity and job satisfaction.
A Smart Investment for Growing Shops
Adding a permanent lift often means construction, new concrete, and a dedicated bay. The Challenger MR6 avoids all of that. It’s a cost-effective way to add lifting capacity, and because it’s portable, it adapts as your shop grows and your layout changes. You can start with one and add more as demand increases.
Great for Dealerships and Prep Lines
Dealerships and used car lots need to inspect and prep many vehicles quickly. The Challenger MR6 lifts a vehicle to a comfortable height in about 45 seconds, giving technicians easy access to tires, brakes, suspension, and the underbody. Because it can operate indoors or out on concrete, it can be set up right where vehicles are being prepped for delivery.
Keeping Your Lift in Top Shape
Set a simple routine: check the hose and fittings daily, inspect the rubber pads and adapters weekly, and follow the manual for fluid checks and lubrication. Keep the lift clean and store it in a dry place when not in use. These small steps help your Challenger MR6 deliver reliable performance year after year.
Choosing Between Mid-Rise Options
Mid-rise lifts vary in height, capacity, and portability. The Challenger MR6 stands out with its 52.75-inch rise, sliding and rotating arms, six lock positions, and dolly-mounted motor. Some mid-rise lifts use fixed platforms, which can be quicker for certain vehicles but less flexible for others. If your shop sees a wide variety of vehicles, the adjustable arms and auxiliary adapters of the Challenger MR6 give you more ways to find the right lift points.
Consider the vehicles you service most, the space you have, and how often you’ll move the lift. Our team is happy to compare options with you so you can choose the lift that best fits your workflow.
Safety Habits for Every Shift
Good habits keep everyone safe. Before each lift, walk around the Challenger MR6 to make sure the area is clear. Check that each pad and adapter is correctly placed. Raise a few inches and confirm the vehicle is stable before lifting higher. Always lower onto a lock before working underneath. When lowering, clear tools and people from the area first. Repeating these steps every time builds a safe, efficient routine for your whole team.
Home Garage Use
While the Challenger MR6 is built with shops in mind, it can also work well in a large home garage. If you have a level concrete floor, a 115V outlet, and a space of at least 10 ft. x 22 ft., you can enjoy mid-rise lifting at home without a tall ceiling or a permanent install. It’s a great step up for serious enthusiasts who do their own brakes, tires, and detailing, and who want more height and comfort than a low-rise lift can provide.
When the work is done, tow the lift aside to free your garage for parking. That flexibility makes the Challenger MR6 a practical choice for home mechanics who want professional-quality equipment without giving up their space.
In every setting, from a busy tire shop to a well-equipped home garage, the Challenger MR6 delivers the same strong, steady, and adaptable lifting that makes everyday service faster and more comfortable.
Ask our team about delivery timing and accessories for the Challenger MR6 today.
We are glad to help you plan your space and get your new lift working quickly.
Frequently Asked Questions About the Challenger MR6
What is the capacity of the Challenger MR6?
It is rated for 6,000 lbs.
How high does it lift?
The rise height is 52.75 inches, with a maximum pad height of 60 inches.
How fast does it rise?
About 45 seconds.
What power does it need?
A 1 HP, 115V, 60Hz, single-phase motor.
How many lock positions does it have?
Six safety lock positions.
Is the Challenger MR6 portable?
Yes. The motor is mounted on a heavy-duty tow dolly, and the lift can operate on concrete indoors or outdoors.
What size bay does it need?
At least 10 ft. x 22 ft. is recommended.
Are adapters included?
Yes. Short and tall auxiliary adapters come standard.
Support From Ironside Garage
Our team can help you confirm space, power, and vehicle fit for the Challenger MR6, and we’ll help coordinate delivery. Contact us with any questions before or after your order.
Order the Challenger MR6 Today
The Challenger MR6 is a proven, powerful, and portable mid-rise lift that helps shops and garages work faster and more comfortably. Explore more options in our full car lifts collection.
Related products
Atlas 6MR Portable Mid-Rise 6000 lb Capacity Scissor Lift
BendPak LR-10000 10000 lb Capacity Low-Rise Lift
BendPak LR-10000 10000 lb Capacity Low-Rise Lift BendPak’s 10,000-lb. capacity LR-10000 low-rise lift is your solution for quick service and increased productivity when servicing today’s passenger cars and light trucks. From tire and brake service to vehicle detailing and body repair, a wide variety
BendPak MDS-6EXT Car Lift
BendPak MDS-6LP 6000 lb Capacity Mid-Rise Scissor Lift
BendPak MDS-6LP 6000 lb Capacity Mid-Rise Scissor Lift We’re not just talking a big game; we’re offering the first open-center mid-rise lift ever made. Decades of experience have taught us a thing or two about vehicle lift points. A car lift with longer platforms means you get to lift more vehicle t
BendPak MDS-6LP Car Lift
BendPak MDS-6LP Car Lift The MDS-6LP sports an open-center design which makes it one of the best options in terms of convenience and work productivity. This lift can handle vehicles weighing up to 6,000 lbs. BendPak has crafted this lift for home garages, full-service shops, quick-lube pits, and rea
BendPak SP-7XE Car Lift
BendPak SP-7XE Car Lift The SP-7XE is a space-saving, frame engaging lift from BendPak. This high-quality lift features no cross members at all, meaning installation is easier than ever. This lift can easily accommodate most passenger vehicles as well as light trucks, and it comes loaded with pneuma
Tuxedo LR-10K-TLPAD 10,000 lbs Commercial Low Rise Pad Lift
The iDEAL LR-10K-TLPAD is a 10,000 lb. low rise, high-performance commercial, vehicle frame contact lift designed for Cars, SUVs, Vans & Trucks. The LR-10K-TLPAD Pad Lift includes the latest in design & safety features including, twin hydraulic cylinders, three locking height positions with dual lat

Reviews
There are no reviews yet.