AFF 547SD 50 25 Ton 2 Stage Air Hydraulic Axle Jack
$2,530.00
AFF 547SD 50 25 Ton 2 Stage Air Hydraulic Axle Jack Capacity: 50 / 25 Tons Ram Lift: 4.61″ / 9.09″ Low Height: 8.46″ / 8.46″ High Height: 13.07″ / 17.56″ High Height w/Ext.: 18.82″ / 23.31″ Working Air Pressure: 116 to 174 psi Ship Weight: 165 lbs.
The AFF 547SD is a super heavy-duty, 2-stage air hydraulic axle jack rated at 50 tons and 25 tons. It is built tough for the rigors of heavy-duty trucking, agricultural, and fleet work. The 547SD uses an industrial-grade piston head seal for a better hold under severe loads, double polished chrome pistons, a single-piece base, and a built-in overload safety valve. An extra-long 54-inch handle locks in three positions, and integral descent metering keeps lowering controlled and safe.
This guide covers the 547SD features, how a 2-stage axle jack works, where to use it, safe lifting, maintenance, and common questions. If your shop needs heavy-duty shop equipment for trucks and equipment, the AFF 547SD is built for the job.
SUPER HEAVY DUTY, 2 Stage 50 Ton and 25 Ton built tough for the rigors of the Heavy Duty• Trucking, Agricultural and Fleet business
The piston head seal design is borrowed from Industrial technology providing a superior low and high pressure seal, giving this jack a much better hold under severe load conditions
The extra long 138cm (54”) handle can be locked in 3 positions for easy positioning of this jack in hard to reach places.
Integral Descent Metering maintains a controlled and safe lowering of the load
Single piece base construction provides superior strength for increased load stability
Double polished chromed pistons allow for much tighter tolerances which reduce oil bypassing and reduced ram scoring
Air assisted lowering speeds up ram retraction
Built in overload safety valve prevents damage to unit due to excessive load
Comes with 2 extensions (75mm/3” + 45 mm1.75”) and saddle adapter
AFF 547SD Features at a Glance
- 2-stage design rated at 50 tons and 25 tons
- Air hydraulic operation
- Industrial piston head seal for superior low- and high-pressure sealing
- Extra-long 54-inch (138 cm) handle that locks in 3 positions
- Integral descent metering for controlled, safe lowering
- Single-piece base construction for load stability
- Double polished chrome pistons for tighter tolerances
- Air assisted lowering for faster ram retraction
- Built-in overload safety valve
- Includes 2 extensions (75 mm / 3 in. and 45 mm / 1.75 in.) and a saddle adapter
What Is a 2-Stage Axle Jack?
A 2-stage axle jack has two rams, one inside the other. The first stage is the larger ram, which provides the highest capacity. The second stage extends from inside the first to give extra lift height, at a lower capacity. On the 547SD, the stages are rated at 50 tons and 25 tons.
This design lets a single compact jack start low enough to fit under heavy truck axles and still lift high enough to clear large tires. Heavy-duty shops use 2-stage axle jacks for tire changes, brake work, and suspension repairs on trucks, buses, tractors, and trailers.
When using any multi-stage jack, always know the load and which stage will carry it. The higher capacity applies to the first stage, and the second stage carries the lower rating. Keep every lift within the rating for the stage in use.
Key Features of the AFF 547SD
Industrial Piston Head Seal
The piston head seal design is borrowed from industrial technology. It provides a superior seal at both low and high pressure, which gives the 547SD a much better hold under severe load conditions. A good seal helps the jack hold its height without creeping down during the job.
Extra-Long 54-Inch Locking Handle
The 54-inch (138 cm) handle can be locked in three positions. That makes it easier to position the jack in hard-to-reach places, such as under axles behind dual wheels or under equipment with low clearance. A long handle also keeps the operator farther from the load.
Integral Descent Metering
Integral descent metering maintains a controlled, safe lowering of the load. Heavy axles come down at a steady rate instead of dropping quickly, which protects the operator, the vehicle, and the jack.
Single-Piece Base
The single-piece base construction provides superior strength and increased load stability. A solid base spreads the load and resists flexing under heavy weight.
Double Polished Chrome Pistons
Double polished chrome pistons allow much tighter tolerances. Tighter tolerances reduce oil bypassing and help prevent ram scoring, so the jack lifts smoothly and lasts longer.
Air Assisted Lowering
Air assisted lowering speeds up ram retraction. After the job, the rams return faster, so the jack is ready for the next lift sooner.
Overload Safety Valve
A built-in overload safety valve helps prevent damage to the unit from excessive loads.
Extensions and Saddle Adapter Included
The 547SD comes with two extensions, one 75 mm (3 in.) and one 45 mm (1.75 in.), plus a saddle adapter. Extensions add starting height when the axle sits higher, and the adapter helps the saddle fit different lift points.
How the 547SD Works
The 547SD is an air hydraulic jack. Compressed shop air powers a pump that forces hydraulic fluid into the rams. The first-stage ram rises first, carrying the highest load rating. If more height is needed, the second-stage ram extends from inside the first. Air does the pumping, so technicians can lift heavy truck axles without working a handle by hand.
To lower the load, the operator uses the release control. Integral descent metering keeps the load coming down at a controlled rate. Once the load is off the jack, air assisted lowering pulls the rams back down quickly so the jack can be rolled out.
Follow the owner’s manual for the correct air pressure and operating steps for your unit.
Common Uses for the 547SD
- Raising heavy truck axles for tire changes
- Brake drum, shoe, and rotor service
- Wheel bearing and hub work
- Spring, air bag, and suspension repairs
- Tractor and combine axle service
- Bus and coach maintenance
- Trailer axle repairs in yards and terminals
- Construction equipment service

Using the Extensions and Saddle Adapter
Heavy vehicles vary a lot in axle height. A low-profile trailer may have little clearance, while a loaded dump truck or tractor may sit high. The two included extensions, 3 inches and 1.75 inches, let you raise the starting height of the saddle so less of the ram stroke is used just to reach the axle. That leaves more stroke for lifting.
Use the shortest setup that reaches the lift point securely. Make sure each extension is fully seated, and never stack parts that are not designed to work together. The saddle adapter helps the jack match different axle shapes and lift points.

Choosing a Lift Point
Always lift at a point approved by the vehicle or equipment manufacturer. For axle jacks, this is usually directly under the axle near the wheel end. Do not lift on brake parts, air lines, shock mounts, or suspension parts that are not designed to carry the load. Center the saddle so the load sits evenly. If the saddle is off center, lower the jack and reposition it before lifting.
Step-by-Step: Lifting an Axle With the 547SD
- Park the vehicle on a hard, level surface and set the parking brakes.
- Chock the wheels that will stay on the ground, on both sides.
- Connect the 547SD to your shop air supply.
- Lock the 54-inch handle in the position that best fits the space.
- Roll the jack under the axle and center the saddle under the lift point.
- Add an extension or the saddle adapter if needed.
- Raise the jack until the saddle contacts the axle, then check the position.
- Lift slowly to the height needed. Stay within the rating for the stage in use.
- Place rated axle stands under the axle.
- Lower the axle onto the stands using the descent control.
- Never work under a vehicle supported only by a jack.
When the work is done, raise the axle off the stands, remove them, and lower the vehicle slowly. Air assisted lowering then returns the rams quickly.
Safety Tips for Heavy-Duty Axle Jacks
- Never exceed the rated capacity for the stage in use.
- Use the jack only on hard, level surfaces.
- Always chock the wheels before lifting.
- Support the vehicle on rated stands before working under it.
- Keep hands and feet away from the saddle and load.
- Lower loads slowly and in a controlled way.
- Inspect the jack before each use for leaks or damage.
- Disconnect the air supply before servicing the jack.
For general guidance on safe use of tools and lifting equipment, see OSHA’s hand and power tools resources.
AFF 547SD Maintenance Tips
- Check hydraulic oil. Keep oil at the level and type listed in the owner’s manual.
- Inspect for leaks. Check seals, fittings, and the rams before each use.
- Protect the pistons. Wipe dirt off the chrome pistons to help prevent scoring.
- Use clean, dry air. Drain compressor tanks and use a water separator to protect the air pump.
- Check the handle locks. Make sure all three positions lock firmly.
- Inspect extensions and adapter. Look for damage or wear before use.
- Store properly. Store the jack with the rams fully retracted in a dry place.

Built for Trucking, Agriculture, and Fleets
AFF built the 547SD for the rigors of heavy-duty trucking, agricultural, and fleet work. These jobs are hard on tools. Jacks get rolled across rough floors, used outdoors, and asked to lift heavy loads many times a day. The 547SD’s single-piece base, industrial seals, and chrome pistons are made for that kind of use.
In trucking and fleet shops, the 547SD speeds up tire, brake, and suspension work on tractors, straight trucks, and trailers. On farms and at equipment dealers, it lifts tractors, combines, and implements for service. Bus and coach shops use it for wheel-end and suspension work. Wherever heavy axles need lifting, the 547SD is ready.
2-Stage vs. Single-Stage Axle Jacks
A single-stage axle jack has one ram. It can be very strong, but its lift height is limited by the length of that single ram. To get more height from a single-stage jack, the body must be taller, which makes it harder to fit under low axles.
A 2-stage jack like the 547SD nests a second ram inside the first. The jack can start low and still reach a useful height. That makes a 2-stage jack more versatile in a shop that services many different vehicles. The trade-off is that the second stage carries a lower rating, so operators must keep track of which stage is carrying the load.

Air Hydraulic vs. Manual Jacks
Manual hydraulic jacks rely on the operator pumping a handle. For a 50-ton load, that takes many strokes and a lot of effort. Air hydraulic jacks like the 547SD use shop air to do the pumping. Technicians lift faster and with less fatigue, and they can stay focused on positioning and safety. In a busy shop, the time saved on every lift adds up quickly.
Who Should Buy the AFF 547SD?
- Heavy-duty truck repair shops
- Fleet maintenance departments
- Agricultural equipment dealers and farms
- Bus and transit garages
- Commercial tire dealers
- Trailer repair shops
- Construction equipment service centers
Getting the Most From Your 547SD
Train every operator on the 547SD controls, the handle lock positions, and the difference between the 50-ton and 25-ton stages. Keep the extensions and saddle adapter stored with the jack so they are easy to find. Keep rated axle stands next to the jack. Inspect the jack on a regular schedule and keep a simple log of checks and service.
If your shop also services cars and light trucks, our car lifts can round out your bays.

Why Seal Quality Matters in an Axle Jack
When a jack holds a heavy axle in the air, the hydraulic fluid inside is under very high pressure. If the seals let fluid slip past the piston, the load can slowly sink. That is called creeping, and it makes work less predictable. The 547SD uses a piston head seal design borrowed from industrial technology. It seals well at both low and high pressure, so the jack holds its position better under severe load conditions.
The double polished chrome pistons support that seal. Their smooth, tight-tolerance surfaces reduce oil bypassing and help prevent scoring, which can damage seals over time. Together, these features help the 547SD hold steady during long jobs and keep performing well over years of use. Even so, always place rated stands under the load before working beneath it.
Planning Your Heavy-Duty Lifting Setup
An axle jack is one part of a complete heavy-duty lifting setup. Most truck and equipment shops pair a jack like the 547SD with rated axle stands, heavy-duty wheel chocks, wheel dollies for large tires, and a reliable air supply. Install air drops close to the bays where heavy vehicles are serviced so the jack can be connected quickly. Keep the floor clean and level so the jack rolls easily and sits steady under load.
Write a simple lifting procedure for your shop and post it near the bays. Include steps for chocking, choosing the lift point, checking which stage will carry the load, placing stands, and lowering slowly. Clear steps help new technicians learn faster and keep everyone working safely.
The Value of a Long Handle
Heavy trucks and equipment often have axles hidden behind dual wheels, mud flaps, fuel tanks, and steps. Getting a jack under the right spot can be awkward. The 547SD’s 54-inch handle helps with that. It lets the operator steer the jack into tight spaces while standing clear of the vehicle, and locking it in one of three positions keeps it out of the way during the lift. A longer reach also keeps the operator’s body farther from the load, which is a simple but important safety benefit.
Frequently Asked Questions About the 547SD
What is the capacity of the AFF 547SD?
The 547SD is a 2-stage jack rated at 50 tons and 25 tons.
Is the 547SD air powered?
Yes. It is an air hydraulic axle jack.
How long is the handle?
The handle is 54 inches (138 cm) long and locks in three positions.
What comes with the 547SD?
It comes with two extensions, 75 mm (3 in.) and 45 mm (1.75 in.), and a saddle adapter.
Does it have an overload valve?
Yes. A built-in overload safety valve helps prevent damage from excessive loads.
How does lowering work?
Integral descent metering keeps lowering controlled and safe, and air assisted lowering speeds up ram retraction.
What makes the seals different?
The piston head seal design is borrowed from industrial technology and provides a superior low- and high-pressure seal for a better hold under severe loads.
Why are the pistons chrome?
Double polished chrome pistons allow tighter tolerances, which reduce oil bypassing and ram scoring.
Who is the 547SD built for?
It is built for heavy-duty trucking, agricultural, and fleet businesses.
Order the AFF 547SD Axle Jack Today
The AFF 547SD 2-stage 50/25-ton air hydraulic axle jack brings industrial seals, chrome pistons, a single-piece base, a 54-inch locking handle, and controlled lowering to your heavy-duty shop. It comes with two extensions and a saddle adapter, ready for trucks, tractors, buses, and trailers. Contact Ironside Garage with questions, and browse our full range of shop equipment.
Related products
BendPak Bender
BendPak Bender heavy-duty “Blue-Bullet” exhaust pipe bender. This high-quality bender takes off like a shot and helps you reach your production target every time. Your purchase of the BB-2 comes complete with a die package and a dual-function end-finishing unit for precision OE expansions and flares
Flo-Dynamics TS410 ATF Inline Exchanger
Mahle CSP-75 75 Ton Shop Press
Ranger RS-500DS
Ranger RS-750DS
Ranger RS-750DS The incredible RS-750DS is made out of rust-free stainless-steel and has a 1,000 lb. weight capacity that can hold some of the biggest car, truck, and SUV parts on the market. This stainless steel 53-gallon capacity spray wash cabinet can rapidly degrease dirty parts, including large

Reviews
There are no reviews yet.