BendPak HD-973PX 9,000 and 7,000 Lb. Capacity / Tri-Level Parking Lift / Extended / High Lift / SPECIAL ORDER

$26,195.00

The longer, higher triple decker The tri-level HD-973PX is a four-post parking lift that maximizes your parking capacity without adding any additional real estate. Each HD-973PX houses up to three vehicles on strengthened parking platforms to give you the most space for your buck. With an additional

SKU: IRG0331 Categories: ,
Description

The BendPak HD-973PX is the extended-length, high-rise version of BendPak’s tri-level parking lift. It stacks three vehicles in one space, with a 9,000 lb. lower deck and a 7,000 lb. upper deck, independent platforms, and full-length aluminum decking. The HD-973PX suits longer and taller vehicles in shops and home garages.

Proprietary design

Shortened height columns allow this car lift to fit in low ceiling spaces where others systems can’t. Although shorter in stature than most tri-level systems, the lower space still yields a full 70 inches of rise.

Independent platforms

Typical multi-level car stackers include a bottom platform that is suspended from the upper platform via chains or cables—both platforms move simultaneously. This tethered operation results in limited spacing options between platforms, as the distance between platforms is fixed.

The HD-973PX features independently operated lifting platforms, permitting varied vehicle heights and spacing in either upper or lower parking spaces. Because the platforms do not have to move in unison with one another, you can now lower the bottom platform without disrupting the overhead vehicle being stored. This allows operators to control one platform at a time. Practically speaking, if you only want to swap out the second-level vehicle, you don’t have to lower the top-level vehicle.

Unmatched protection

The patent-pending design of the HD-973PX features multi-position safety locks that are spaced just four inches apart. This allows almost unlimited parking height arrangements on either the upper or lower decks. Redundant, anti-fall, spring-loaded safety catches immediately halt downward movement of either platform in the unlikely event of cable failure.

Hydraulic power

A powerful hydraulic cylinder is enclosed underside each platform set and is matched with high-strength lifting cables for simplicity and dependability. The lift can be configured for drive-thru operation, allowing as many as three deep for maximum efficiency and better use of space.

Smarter construction means less cost to you

High-rise parking lifts that can fit three vehicles will inevitably cost more than other lifts. There’s simply more steel involved, and larger lifts require additional engineering, all of which gets incorporated in the cost. The HD-973PX offsets much of that extra cost because its smart design requires less steel. The end result is an incredibly efficient parking lift that actually saves buyers thousands of dollars while upholding the industry’s most rigid safety standards.

Weight-displacing base

Specially designed base frames distribute the load, which makes this unique lifting system suitable for installation on virtually any residential or commercial concrete floor. It can even be installed on asphalt when equipped with concrete footers. The HD-973PX may be configured as a stand-alone lift or combined into rows of multiple units.

Who should get this parking lift?

Explore the HD-973PX if you need to stack three vehicles in a tight space, or if you want the versatility to vary the parking heights of your second and third-level vehicles. The lift’s small footprint and exemplary design makes for an ideal lifting solution in both professional shops and home garages.

Features & Specs

  • Extended length, high rise
  • Perfect for parking, storage and service
  • 7,000 lb. capacity upper deck
  • 9,000 lb. capacity lower deck
  • Superstructure features durable powder coat finish
  • Perfect for cars, trucks, and SUVs
  • Platforms feature full-length aluminum decking
  • Rugged welded-steel construction
  • Powerful hydraulic cylinders
  • Heavy-duty 3/8” lifting cable
  • Heavy-duty steel construction
  • Wide base-plate for maximum stability
  • Heavy-duty steel construction
  • Grease nipples are located on every sheave and sheave axle to make lubrication maintenance a breeze
  • Integrated hydraulic flow restrictor provides controlled descent in event of hose rupture
  • Reliable electric-hydraulic power system
  • Runways feature non-skid surface
  • Multi-position safety locks in each column
  • Automatic safety locks combined with redundant anti-fall devices
  • Adjustable lock ladders
  • Independent backup slack-cable safety latches
  • Push-button pneumatic safety release.
  • Padded trip bar with limit switch prevents lower vehicle from making contact with upper platform.
  • Simple controls
  • Optional drive-thru ramps available
  • Optional 4,500-lb. air-hydraulic rolling jacks available

Style

Style:
Multi-Level Parking Lift

Top Platform

Lifting Capacity*
7,000 lbs. (3,175 kg)
*Max Capacity / Front Axle
3,500 lbs. (1,588 kg)
*Max Capacity / Rear Axle
3,500 lbs. (1,588 kg)
A – Overall Width
112″ (2,84​9 mm)
B – Overall Length
252.25″ (6,409 mm)
C – Height of Columns
245″ (6,227 mm)
D – Drive-thru Clearance
87″ (2,201 mm)
E – Maximum Rise
151.5″ (3,​849 mm)
F – Maximum Lifting Height
156.5″ (3,972 mm)
G – Distance Between Columns
100″ (2,546 mm)

Top Platform (continued)

H – Runway Width
19″ (482 mm)
I – Width Between Runways
44″ (1,121 mm)
J – Runway Length
199″ (​5,056 mm)
Min. Wheelbase @ rated Capacity1
1​40″ (3,​556 mm)
Min. Wheelbase @ 75% Capacity1
1​20″ (​3,084 mm)
Min. Wheelbase @ 50% Capacity1
​100″ (2,​540 mm)
Min. Wheelbase @ 25% Capacity1
80″ (2,032 mm)
Locking Positions
3​4
Locking Spacing
Every 4″ (102 mm)
Lifting Time to Max. Rise
90 seconds
Motor
220 VAC / 60 Hz / 1 Ph

Bottom Platform

Lifting Capacity*
9,000 lbs. (4,082 kg)
*Max Capacity / Front Axle
4,500 lbs. (2,041 kg)
*Max Capacity / Rear Axle
4,500 lbs. (2,041 kg)
A – Overall Width
112″ (2,842 mm)
B – Overall Length
252.25″ (6,409 mm)
C – Height of Columns
245″ (6,227 mm)
D – Drive-thru Clearance
90.25″ (2,2​95 mm)
E – Maximum Rise
​82.25″ (​2,088 mm)
F – Maximum Lifting Height
87.25″ (​2,211 mm)
G – Distance Between Columns
100″ (2,546 mm)

Bottom Platform (continued)

H – Runway Width
19″ (482 mm)
I – Width Between Runways
44″ (1,121 mm)
J – Runway Length
186.75″ (4,​744 mm)
Min. Wheelbase @ rated Capacity1
1​35″ (3,​429 mm)
Min. Wheelbase @ 75% Capacity1
1​15″ (2,​921 mm)
Min. Wheelbase @ 50% Capacity1
​95″ (2,​413 mm)
Min. Wheelbase @ 25% Capacity1
7​5″ (1,​905 mm)
Locking Positions
1​6
Locking Spacing
Every 4″ (102 mm)
Lifting Time to Max. Rise
50 seconds
Motor
220 VAC / 60 Hz / 1 Ph

1The Lift supports less weight than its rated capacity when the vehicle’s wheelbase is shorter; this is because the wheels of such a vehicle are closer to the middle of the Runways, where there is less strength. For example, the maximum weight allowed on the Lift for a vehicle with a wheelbase of 95″ is 50 percent of the Lift’s rated capacity (or 3,500 lbs. when the rated capacity is 7,000 lbs.).

HD-973PX Features

  • Extended length and high rise
  • Stores three vehicles in a single parking space
  • 9,000 lb. lower deck and 7,000 lb. upper deck
  • Independently operated platforms
  • Full-length aluminum decking on the platforms
  • Rugged welded-steel construction with a powder-coat finish
  • Load-distributing base frames for residential or commercial concrete floors
  • Can be installed on asphalt with concrete footers
  • Stand-alone or combined into rows of multiple units
  • For parking, storage, and service of cars, trucks, and SUVs
  • Special-order item

Why Choose the Extended, High-Rise Version?

The standard tri-level design is built to fit lower ceilings. The HD-973PX goes the other way: longer platforms and more rise for owners who have the space and want to stack longer and taller vehicles. Extended decks handle long-wheelbase trucks and SUVs, while the higher rise gives more clearance between levels. If your building has the height, the HD-973PX gives you more flexibility in which vehicles go where.

Independent Platforms

Each platform on the HD-973PX works on its own. You can lower the bottom platform without disturbing the vehicle on top, and set each level at the height that suits its vehicle. If you only want to swap the second-level vehicle, the top vehicle stays put. That saves time and gives you more control than tethered stackers, where both platforms move together at a fixed spacing.

Full-Length Aluminum Decking

The platforms feature full-length aluminum decking. A solid deck helps protect the vehicles below from drips and debris, and gives a clean, finished look. Aluminum is also corrosion resistant, which suits both indoor and outdoor installs.

Installs on Most Floors

Specially designed base frames spread the load, making the HD-973PX suitable for virtually any residential or commercial concrete floor. With concrete footers, it can even be installed on asphalt. Always follow BendPak’s installation requirements and local codes.

Single Units or Rows

Install one HD-973PX in a home garage, or line up several in a commercial facility. Multiple units can be combined into rows to multiply capacity across a building or lot.

Who Should Buy the HD-973PX

  • Owners stacking long trucks and SUVs
  • Collectors with tall garages or shop buildings
  • Dealerships storing inventory three high
  • Parking operators looking to triple capacity
  • Professional shops needing storage plus service access

Compare more options in our four-post lifts category.

Using the HD-973PX

  1. Lower the platform you want to load.
  2. Drive on slowly and center the vehicle on the aluminum deck.
  3. Set the parking brake and turn off the engine.
  4. Raise the platform to the chosen height and lower onto the locks.
  5. Repeat for the other platform as needed.
  6. Park the ground-level vehicle beneath the lower deck.

Safety Guidelines

Never exceed 9,000 lbs. on the lower deck or 7,000 lbs. on the upper deck. Always lower each platform onto its locks before parking beneath it. Only trained operators should run the lift, and people should stay clear while platforms move. Follow BendPak’s operating manual and inspect the lift regularly.

Planning Your Space

Because the HD-973PX is extended and high rise, measure carefully. Check the full ceiling height at the installation spot, including beams, lights, sprinklers, and door tracks. Measure bay length for the extended platforms, and confirm floor condition. Plan for power, drive aisles, and turning space. As a special-order lift, it needs extra lead time, so start planning early.

Maintenance Tips

  • Inspect lifting components and hydraulics for wear or leaks.
  • Confirm the locks engage on each platform.
  • Keep the aluminum decking clean.
  • Touch up the powder coat if chipped.
  • Follow BendPak’s service schedule.

HD-973PX vs. HD-973P

BendPak offers two versions of its tri-level lift. The HD-973P has shortened columns so it fits lower ceilings. The HD-973PX is extended in length and higher in rise, so it suits taller spaces and longer vehicles. If your garage or building is height-limited, the HD-973P may be the right call. If you have the room, the HD-973PX gives you more clearance and longer platforms for a wider range of vehicles.

HD-973PX

Parking, Storage, and Service

The HD-973PX isn’t only a stacker. BendPak describes it as perfect for parking, storage, and service. Store a collector car long-term on the top level, keep a second vehicle on the lower deck, and park a daily driver underneath. When you need to inspect or maintain a vehicle, the high rise gives you extra room to work.

A Day With a Triple Stacker

In a typical setup, the ground space holds the vehicle used every day, the lower deck holds one used occasionally, and the top deck holds long-term storage. When someone needs the middle vehicle, the ground-level car moves out, the lower deck comes down, and the vehicle drives off. The top vehicle never moves. Independent platforms keep the process simple and predictable.

HD-973PX tri-level lift

Commercial Benefits

For dealerships and parking operators, triple stacking can dramatically increase capacity without new construction. The HD-973PX’s extended decks accommodate the long trucks and SUVs that make up much of today’s market. Rows of units can transform a storage area or lot into high-density parking.

Collector Garages

Collectors with tall garages can use the HD-973PX to display and store three vehicles in one bay. The aluminum decking protects vehicles below, and the independent platforms make it easy to bring out any car on the lower deck without disturbing the top one.

Choosing Platform Heights

With independent platforms, you can set each deck to suit its vehicle. Start with the ground-level vehicle: measure its roof height and add a safety margin to find the minimum height for the lower deck. Then do the same for the vehicle on the lower deck to find the minimum for the upper deck. Compare the total with your ceiling height. The high rise of the HD-973PX gives you more room to work with, so taller vehicles can often be stacked where other triple stackers would not fit. Post the chosen heights near the controls.

Lighting, Signage, and Training

Good lighting helps drivers position vehicles accurately on each deck. Clear signage showing each deck’s capacity and height limits prevents mistakes. In commercial settings, train every operator on raising, lowering, and lock checks. These steps keep the HD-973PX safe and efficient day after day.

Long-Term Storage Tips

For vehicles stored long-term, keep batteries on maintainers, check tire pressure occasionally, and inspect for leaks. The aluminum decking helps protect the vehicles below, but periodic checks keep all three vehicles in top shape.

Special-Order Planning

Because the HD-973PX is a special-order product, contact our team early. We’ll confirm availability and lead time, help you prepare your site, and coordinate freight delivery so your project stays on schedule.

An Investment in Space

Building new parking is costly and slow. The HD-973PX adds two extra parking spaces in the footprint of one, using vertical space you already have. For owners with tall buildings and long vehicles, it’s one of the most efficient ways to expand capacity.

What Owners Appreciate

Owners of the HD-973PX often highlight the freedom it gives them. Three vehicles fit where one used to, each protected and easy to access thanks to independent platforms. The extended decks mean they don’t have to worry whether a long pickup or full-size SUV will fit, and the high rise leaves room for taller vehicles underneath. For businesses, the added capacity can translate directly into more stored inventory or more customers served from the same building.

If you have a tall space and a growing number of vehicles, the HD-973PX is a practical way to make that space work much harder for you, year after year.

Send us your ceiling height, bay length, and the vehicles you plan to stack, and our team will help you confirm that the HD-973PX is the right fit before you place your special order. We can also help you compare it side by side with the standard tri-level model.

Whatever you store, the HD-973PX keeps every vehicle organized, protected, and within easy reach.

Frequently Asked Questions About the HD-973PX

How many vehicles does the HD-973PX hold?

Three vehicles in one parking space.

What are the capacities?

9,000 lbs. on the lower deck and 7,000 lbs. on the upper deck.

Can it be installed on asphalt?

Yes, when equipped with concrete footers.

Can I install several units together?

Yes. It can be a stand-alone lift or combined into rows.

How is it different from the HD-973P?

The HD-973PX is extended in length and higher in rise; the HD-973P has shortened columns for lower ceilings.

Support From Ironside Garage

Our team can help you measure your space, compare the two tri-level versions, and coordinate the special order and freight delivery. Contact us with any questions about the HD-973PX.

Order the HD-973PX Today

The BendPak HD-973PX is a proven, powerful tri-level lift for long and tall vehicles. Learn more on the official BendPak website, or browse our full car lifts collection.

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “BendPak HD-973PX 9,000 and 7,000 Lb. Capacity / Tri-Level Parking Lift / Extended / High Lift / SPECIAL ORDER”

Your email address will not be published. Required fields are marked *

Shipping & Delivery