Ranger RP 50FC Electro Hydraulic Oil Filter Crusher
$5,695.00
The Ranger RP 50FC Electro Hydraulic Oil Filter Crusher applies 25 tons of electric-hydraulic pressing power to flatten just about any used oil filter to 20% of its original size, all while removing 95% of the residual oil. Filters up to 15.25″ long and 6″ diameter are crushed in seconds flat.
The Ranger RP-50FC is a heavy-duty electro-hydraulic oil filter crusher with 50,000 lbs. (25 tons) of crushing force. It handles automotive and heavy-duty filters up to 15-1/4 inches long and 6 inches in diameter, crushes them to 20% of their original size, and removes up to 95% of the residual oil. An automatic cycle lets an operator load a filter, push a button, and walk away while the RP-50FC does the work. A rugged floor stand holds drums up to 55 gallons for the recovered oil.
This guide covers the full RP-50FC specifications, how it works, its safety features, installation, maintenance, and common questions. If your shop handles large truck and equipment filters and you are shopping for shop equipment that cuts waste costs, the Ranger RP-50FC is built for the job.
Ranger RP 50FC Electro Hydraulic Oil Filter Crusher With Stand / 25-Ton Capacity / Heavy-Duty / 208-240V, 1-Phase, 50/60hz
Features & Specs:
Maximum crushing pressure of 50,000 pounds.
Filters are reduced to 20% of their original size with 95% of residual oil removed.
Automatic cycle feature lets you load the filter, push a button, and walk away.
Fulfills EPA and other mandated environmental standards
Save on waste disposal costs and storage space
Handles automotive and heavy-duty filters up to 15-1/4″ long and 6″ diameter.
Cycle time approximately 8 to 15 seconds depending on filter size.
No-mess design operates clean and efficiently to lessen spill hazards.
Ergonomic controls feature automatic or manual cycles.
Welded steel plate construction
Electric-hydraulic power unit features 2-HP motor.
Automatic safety door stops operation when opened.
Transparent door for a convenient view of the crushing process.
Powered by a 2-HP electric-hydraulic pump with 2-gallon reservoir.
Rugged floor stand is designed to accommodate up to 55-gallon drums for efficient fluid handling.
Overall height: 90.5″ / 2299 mm
Overall width: 32.5″ / 826 mm
Overall depth: 31.5″ / 800 mm
Chamber opening height: 16″ / 406 mm
Chamber opening width: 9.8″ / 249 mm
Chamber opening depth: 11.5″ / 292 mm
Average cycle time: 8 – 15 seconds
Power Supply: 208‐230V, 50/60HZ, 1Ph.
Shipping Weight: 718 lbs. (326 kg)
Shipping Dimensions: 75″ x 35″ x 20″ (1,905 mm x 889 mm x 508 mm)
Ranger RP-50FC Specifications
- Maximum crushing pressure: 50,000 lbs. (25 tons)
- Filter capacity: automotive and heavy-duty filters up to 15-1/4″ long and 6″ diameter
- Filter reduction: to 20% of original size
- Oil removal: up to 95% of residual oil
- Average cycle time: 8-15 seconds, depending on filter size
- Controls: automatic or manual cycles
- Power unit: 2-HP electric-hydraulic pump with 2-gallon reservoir
- Power supply: 208-230V, 50/60 Hz, 1 phase
- Overall height: 90.5″ (2,299 mm)
- Overall width: 32.5″ (826 mm)
- Overall depth: 31.5″ (800 mm)
- Chamber opening height: 16″ (406 mm)
- Chamber opening width: 9.8″ (249 mm)
- Chamber opening depth: 11.5″ (292 mm)
- Floor stand: accommodates up to 55-gallon drums
- Construction: welded steel plate
- Shipping weight: 718 lbs. (326 kg)
- Shipping dimensions: 75″ x 35″ x 20″ (1,905 mm x 889 mm x 508 mm)
Why Choose a 25-Ton Filter Crusher?
Smaller filter crushers work well for passenger car filters, but heavy-duty truck, bus, and equipment filters are bigger, thicker, and hold more oil. They need more force to crush flat and drain completely. The RP-50FC is Ranger’s most powerful oil filter crusher, with 50,000 lbs. of force. That power lets it crush large diesel filters as easily as small automotive ones.
The tall 16-inch chamber opening takes filters up to 15-1/4 inches long. That covers many of the long filters used on heavy trucks, buses, tractors, and construction equipment. If your shop services a mix of cars and big rigs, one RP-50FC can handle nearly all of your filters.
Benefits of Crushing Used Oil Filters
- Lower disposal costs. Crushed filters take about one-fifth of the space, so you need fewer pickups and less storage.
- More recovered oil. Removing up to 95% of the residual oil increases the amount you send for recycling.
- Recyclable metal. Drained steel filters can often go to scrap metal recyclers.
- Cleaner shop. Crushed pucks drip less than whole filters.
- Compliance support. Ranger states the RP-50FC fulfills EPA and other mandated environmental standards.
Used oil and filters must be handled correctly. The EPA used oil management guidance explains the basics, and your state may have more requirements.
How the RP-50FC Works
The RP-50FC uses an electric-hydraulic power unit with a 2-HP motor and a 2-gallon hydraulic reservoir. During a cycle, the hydraulic pump drives the crushing ram down into the chamber with up to 50,000 lbs. of force. The filter is flattened, and the oil trapped in the media and canister is squeezed out.
The oil drains through the crusher into a drum on the floor stand below. The stand fits drums up to 55 gallons, so you can collect a large volume of oil before swapping the drum. Each filter comes out as a compact puck about 20% of its original size.
Most cycles take 8 to 15 seconds, depending on filter size. Fast cycles keep up with a busy fleet shop or lube line.

Automatic and Manual Cycles
The RP-50FC has ergonomic controls that offer automatic or manual cycles. In automatic mode, the operator loads the filter, closes the door, pushes a button, and walks away. The crusher completes the cycle on its own, so the technician can go back to work right away.
Manual mode gives the operator direct control of the ram. This can be useful for unusual filters or when you want to watch and control each stage of the crush. Having both modes lets each shop use the RP-50FC the way that works best for its team.

RP-50FC Safety Features
- Automatic safety door. Operation stops if the door is opened.
- Transparent door. Operators can watch the crushing process without opening the chamber.
- No-mess design. The crusher runs cleanly to reduce spill hazards.
- Welded steel plate construction. Heavy steel plate stands up to repeated 25-ton cycles.
- Ergonomic controls. Controls are placed for comfortable, simple operation.
Train every operator before use. General guidance on working safely with powered machines is available from OSHA’s machine guarding resources.
What Filters Fit in the RP-50FC?
The chamber opening is 16 inches high, 9.8 inches wide, and 11.5 inches deep. Ranger rates the RP-50FC for automotive and heavy-duty filters up to 15-1/4 inches long and 6 inches in diameter. Typical filters include:
- Passenger car and light truck oil filters
- Diesel pickup oil and fuel filters
- Heavy truck and bus oil filters
- Agricultural and construction equipment filters
- Many hydraulic and fuel filters that fit the chamber
Measure your largest filters before ordering and compare them with the 15-1/4-inch length and 6-inch diameter limits.
Installing the RP-50FC
The RP-50FC runs on 208-230V, 50/60 Hz, single phase power. Have a licensed electrician install a properly sized circuit and connect the crusher according to local electrical codes.
Plan the location carefully. The crusher stands 90.5 inches tall, 32.5 inches wide, and 31.5 inches deep, so check overhead clearance from lights, pipes, and doors. Place it on a level concrete floor near the area where filters come off vehicles. Leave room in front for the operator to load filters and room under the stand to swap drums.
The shipping weight is 718 lbs., so plan for a forklift or pallet jack at delivery. Once the crusher is in place, make sure it sits level and steady before use.
Since the stand holds drums up to 55 gallons, use a drum dolly or drum truck to move full drums. Keep spill absorbent nearby for drips during drum changes.

Step-by-Step: Crushing a Filter in Automatic Mode
- Check that the drum on the floor stand has room for more oil.
- Open the transparent door and place the filter upright in the chamber.
- Close the door so the automatic safety door system allows operation.
- Select automatic mode and push the start button.
- Walk away or watch through the transparent door as the RP-50FC crushes the filter.
- When the cycle ends, open the door and remove the crushed puck.
- Put the puck in your scrap metal or filter recycling container.
A full cycle takes about 8 to 15 seconds, so a stack of filters can be crushed quickly at the end of a shift or as each oil change finishes.
RP-50FC Maintenance Tips
- Check hydraulic fluid. Keep the 2-gallon reservoir at the right level and look for leaks at hoses and fittings.
- Clean the chamber. Remove debris and oil buildup so filters sit flat.
- Test the safety door. Confirm the crusher stops when the door opens.
- Keep the window clean. A clear transparent door lets operators see the process.
- Watch the drum level. Swap drums before they get too full.
- Check fasteners and the stand. Tighten bolts and inspect welds periodically.

Who Should Buy the Ranger RP-50FC?
- Heavy-duty truck and diesel repair shops
- Fleet maintenance garages for trucks and buses
- Agricultural and construction equipment dealers
- Municipal and government vehicle shops
- High-volume quick-lube centers
- Dealerships that service both cars and trucks
If your shop sees large diesel filters every week, a smaller crusher may struggle with them. The RP-50FC gives you the force and chamber size to handle big filters with ease.
RP-50FC vs. Smaller Filter Crushers
Ranger also makes smaller crushers, such as the 20,000-lb. RP-20FC and the 30,000-lb. RP-30FCH. Those models are a good fit for automotive and light truck filters. The RP-50FC steps up to 50,000 lbs. of force, adds an automatic cycle, and offers a taller 16-inch chamber opening for filters up to 15-1/4 inches long. If you work on heavy equipment or big trucks, the extra capacity of the RP-50FC is worth it.

Building a Filter Recycling Program
The RP-50FC is the heart of a simple recycling routine. Use one labeled drum for drained oil and one labeled container for crushed filters. Crush filters as they come off vehicles so they do not pile up. Keep oil drums closed when not in use and store them away from floor drains.
Ask your used oil hauler about pickup schedules and whether they accept drained filters. Contact local scrap metal recyclers to find one that takes crushed oil filters. Keep records of pickups and amounts. Records help show that waste is handled correctly and make it easy to track the savings from the RP-50FC.
Safety Tips for Using the RP-50FC
- Wear gloves and safety glasses when handling used filters and oil.
- Keep hands out of the chamber while the ram is moving.
- Never bypass the automatic safety door.
- Keep the floor around the crusher clean and dry.
- Only trained employees should operate the RP-50FC.
- Store used oil in approved, labeled containers.
How the RP-50FC Saves Money
The savings from a filter crusher come from several sources at once. First, crushed filters take up far less room. Since each filter shrinks to about 20% of its original size, the same container holds roughly five times as many filters. That means fewer pickups and less money spent on hauling.
Second, the oil you recover has value. With up to 95% of the residual oil removed from each filter, a busy truck shop can collect a large volume of used oil every month. Many used oil collectors will pick it up at low cost, and in some areas they may pay for it.
Third, drained steel casings can often be sold or given to scrap metal recyclers instead of being handled as oily waste. Heavy-duty filters contain a lot of steel, so the scrap volume adds up quickly.
Finally, the automatic cycle saves labor. A technician can load the RP-50FC, push the button, and return to billable work while the crusher finishes. Over a year, these small savings can make the RP-50FC one of the most cost-effective machines in the shop.

Where to Place the RP-50FC in Your Shop
Put the crusher close to where oil changes happen, such as the lube pit, the heavy truck bays, or the fluid service area. A short walk from the vehicle to the crusher means filters do not sit on the floor or in buckets. Keep the drum area clear so full drums can be rolled out easily. Good lighting around the crusher helps operators see the chamber and the transparent door clearly.
If you are planning a new service area, think about crushers, drain equipment, and lifts together. Our car lifts section can help you lay out bays and fluid service space at the same time.

RP-50FC vs. Gravity Draining
Some shops still drain filters by turning them upside down over a pan or a funnel. Gravity draining takes many hours, sometimes a full day, and still leaves a large amount of oil soaked in the filter media. The filters also take up shelves, buckets, and floor space while they drip. Large heavy-duty filters are even slower to drain because they hold more oil.
The RP-50FC removes up to 95% of the oil in about 8 to 15 seconds and reduces each filter to 20% of its original size. Instead of rows of dripping filters, you get a neat stack of flat pucks and a drum of collected oil. The work area stays cleaner, and the risk of slips and spills goes down.
Electro-Hydraulic Power Explained
The RP-50FC uses an electric motor to drive a hydraulic pump. Hydraulic systems can produce very high force from a compact power unit, which is why the RP-50FC can reach 50,000 lbs. with only a 2-HP motor. Because it runs on electricity, it does not depend on your shop air compressor, so crushing filters will not take air away from impact tools, tire machines, or lifts. The 2-gallon reservoir holds the hydraulic fluid that powers the ram.
Frequently Asked Questions About the RP-50FC
How much force does the RP-50FC produce?
It delivers a maximum crushing pressure of 50,000 lbs., or 25 tons.
What size filters does it handle?
It handles automotive and heavy-duty filters up to 15-1/4 inches long and 6 inches in diameter.
How much oil does it remove?
The RP-50FC removes up to 95% of the residual oil.
How small does it crush filters?
Filters are reduced to about 20% of their original size.
Does it have an automatic cycle?
Yes. You can load the filter, push a button, and walk away. Manual cycles are also available.
What power does it need?
It runs on 208-230V, 50/60 Hz, single phase power with a 2-HP electric-hydraulic pump.
What size drum fits under it?
The floor stand accommodates drums up to 55 gallons.
How tall is the RP-50FC?
The overall height is 90.5 inches.
What is the shipping weight?
The RP-50FC ships at 718 lbs. (326 kg).
Order the Ranger RP-50FC Today
The Ranger RP-50FC electro-hydraulic oil filter crusher brings 25 tons of force, an automatic cycle, and a tall chamber for heavy-duty filters to your shop. It removes up to 95% of the oil, shrinks filters to 20% of their size, and keeps your recovered oil neatly stored in a drum below. Contact Ironside Garage with questions about power or delivery, and browse more shop equipment for your service bays.
Related products
Atlas Automotive Equipment Spray Wash Cabinet
Atlas Automotive Equipment Spray Wash Cabinet The Atlas 500 Spray Wash Cabinet is the ideal parts washer for any automotive repair shop. The 1,000 lb. capacity turntable is strong enough for any size auto or light truck engine. The cut-away sides under the door allow you to wheel your engine crane r
Cool Boss CB-28L Portable Evaporative Air Cooler
Cool Boss CB-28L Portable Evaporative Air Cooler The CB-28 is a medium-duty commercial-grade cooler that is well-suited for large industrial space cooling. When temperatures rise and you’re looking for a cost-effective cooling solution, look no further than Cool Boss. The CB-28 evaporative cooler pu
Mahle FluidPRO ATX 280 Transmission Fluid Exchange System with Adapters
Portacool Apex 1200 Wi-Fi Enabled High Velocity Portable Evaporative Cooler for 1200 sq ft
Portacool Apex 1200 Wi-Fi Enabled High Velocity Portable Evaporative Cooler for 1200 sq ft Meet the Portacool APEX™ 1200—a game-changer for mid-sized spaces demanding serious cooling. Delivering a powerful 4,000 CFMs of airflow that spans up to 40 ft., this unit ensures consistent comfort across 1,2

Reviews
There are no reviews yet.