Atlas Automotive Equipment Spray Wash Cabinet
$3,500.00
Atlas Automotive Equipment Spray Wash Cabinet The Atlas 500 Spray Wash Cabinet is the ideal parts washer for any automotive repair shop. The 1,000 lb. capacity turntable is strong enough for any size auto or light truck engine. The cut-away sides under the door allow you to wheel your engine crane r
The Atlas STW-500 is a heavy-duty automotive spray wash cabinet built for shops that clean engine blocks, cylinder heads, transmissions, and other greasy parts every day. The STW-500 combines a 50-gallon heated tank, a 1,000-lb. capacity turntable, 19 adjustable steel nozzles, and a 43 GPM water pump in a powder-coated cabinet. Load the parts, close the door, set the 60-minute timer, and the STW-500 does the scrubbing while your technicians move on to other work.
This page covers the full STW-500 specifications, how the cabinet works, what fits inside it, installation and power needs, cleaning chemistry, maintenance, and answers to common questions. If you are comparing parts washers and other shop equipment, the details below will help you decide whether the Atlas STW-500 is the right size for your work.
Atlas Automotive Equipment Spray Wash Cabinet
Features and Benefits:
50 Gallon Tank Capacity
Powder Coat Finish (Exterior)
Heavy Duty Construction
1,000 lb. Capacity Turntable
Heater Element Heats to 135F-175F
60 Minute Timer with Automatic Shut-Off
19 Adjustable Steel Nozzles
43 GPM Water Pump
Oil Skimmer Included
Tree Rack and Parts Basket Included
1 yr Warranty – Limited Parts Only
This part number FREIGHT PREPAID
Atlas STW-500 Specifications
Tank Capacity: 50 Gallons
Inside Height: 42″
Inside Width: 32″
Turntable Diameter: 30″
Overall Dimensions: 44 3/8″ L x 44 1/8″ W x 66 3/4″ H
Turntable Load Capacity: 1000 lb
Cycle Time: 60 min. std.
Pump Output: 28 PSI @ 43 GPM
Power Supply: 220volt/Single (1) Phase (30 Amp Breaker Required)
Motor: 1.5HP
Shipping Weight: 750 lbs
Atlas STW-500 Specifications at a Glance
Before you buy any spray wash cabinet, you need to know whether your largest parts will fit and whether your building can supply the power. Here are the published Atlas STW-500 specifications:
- Tank capacity: 50 gallons
- Inside height: 42 inches
- Inside width: 32 inches
- Turntable diameter: 30 inches
- Turntable load capacity: 1,000 lbs.
- Overall dimensions: 44 3/8″ L x 44 1/8″ W x 66 3/4″ H
- Cycle time: 60 minutes standard
- Pump output: 28 PSI at 43 GPM
- Motor: 1.5 HP
- Heater: heats solution to 135°F-175°F
- Power supply: 220 volt, single phase (30 amp breaker required)
- Shipping weight: 750 lbs.
- Warranty: 1 year, limited parts only
The STW-500 ships freight prepaid. Because the shipping weight is 750 lbs., plan for a forklift or pallet jack at delivery and a clear path to the spot where the cabinet will live.
How the STW-500 Spray Wash Cabinet Works
A spray wash cabinet works a lot like a dishwasher for auto parts. The STW-500 holds 50 gallons of water and cleaning solution in a tank under the wash chamber. The heater element brings that solution up to a working temperature between 135°F and 175°F. Warm solution breaks down grease, oil, and road grime much faster than cold water does.
When you start a cycle, the 1.5 HP motor drives a pump that pushes solution at 43 gallons per minute through 19 adjustable steel nozzles. The nozzles aim the spray at the parts from several angles. At the same time, the force of the spray turns the 30-inch turntable, so every side of the part passes through the spray pattern. The used solution drains back into the tank, where it is heated and pumped again.
The 60-minute timer lets you set the cycle length. When the time runs out, the STW-500 shuts off on its own. That automatic shut-off means a technician can load the cabinet, start it, and walk away without worrying about the machine running all night.
An oil skimmer is included. As the cabinet runs, oil floats to the top of the solution in the tank. The skimmer removes that oil so it does not get pumped back onto clean parts. Removing oil also helps the cleaning solution last longer between full changes.
What Fits Inside the STW-500
The wash chamber of the STW-500 measures 42 inches high and 32 inches wide, and the turntable is 30 inches across. That space handles most passenger car and light truck components. Common parts that shops clean in a cabinet this size include:
- Four-cylinder, V6, and V8 engine blocks
- Cylinder heads and intake manifolds
- Automatic and manual transmission cases
- Differential housings and axle parts
- Oil pans, valve covers, and timing covers
- Brake calipers, brackets, and suspension parts
- Small engine and motorcycle components
The turntable is rated for 1,000 lbs. That rating is the most important number when you clean heavy cast iron parts. A bare cast iron V8 block can weigh several hundred pounds, so the STW-500 gives you room to wash a block along with smaller parts in the basket. Always check the weight of your heaviest load and stay under the turntable rating.
Measure your tallest parts before you order. A part should clear the top of the chamber with room to spare, and wide parts should spin freely on the turntable without hitting the nozzle pipes. If you regularly clean very tall or very heavy truck parts, a larger cabinet may suit you better. For most general repair and engine rebuild shops, the STW-500 is a practical middle size.


Included Accessories: Tree Rack and Parts Basket
The Atlas STW-500 comes with a tree rack and a parts basket. The tree rack lets you hang smaller parts, such as brackets, rods, and covers, so the spray can reach every surface. The parts basket holds loose items like bolts, rocker arms, lifters, and other small hardware that would otherwise fall through the turntable.
Using the rack and basket together lets you clean a full engine teardown in one cycle. Put the block on the turntable, hang the heads and covers on the tree, and drop the small hardware in the basket. One load, one timer setting, and the whole job comes out clean.
Build Quality and Construction
The STW-500 uses heavy-duty construction with a powder coat finish on the exterior. Powder coating is tougher than ordinary paint and stands up better to the chemicals, heat, and moisture found in a wash bay. The steel nozzles are adjustable, so you can aim them at the areas that need the most cleaning and change the pattern for different parts.
Inside, the cabinet is built to handle heated water and cleaning solution every day. Heavy-duty construction matters in a spray washer because the pump, heater, and turntable run for long cycles, and the cabinet has to support up to 1,000 lbs. of parts plus 50 gallons of solution.
STW-500 Power and Installation Requirements
The STW-500 runs on 220 volt, single phase power and requires a 30 amp breaker. Many shops already have 220V single phase service for air compressors, lifts, and welders, but the cabinet should have its own properly sized circuit. Have a licensed electrician check your panel, install the breaker, and make the connection according to local electrical codes.
Plan the location before the cabinet arrives. The overall footprint is 44 3/8 inches long by 44 1/8 inches wide, and the cabinet stands 66 3/4 inches tall. Leave extra space in front so the door can open fully and parts can be loaded with a hoist or engine crane. Leave room on the sides and back for service access to the pump, heater, and drain.
Set the STW-500 on a level concrete floor that can handle the weight of the cabinet, the full tank, and a load of parts. Fifty gallons of water alone weighs over 400 lbs., so the total weight of a loaded machine is significant. A level floor also helps the turntable spin evenly and keeps the tank draining correctly.
Think about water supply and drainage, too. You will need a convenient way to fill the tank and a legal way to dispose of used solution and sludge. Used parts washer solution often contains oil, heavy metals, and other contaminants. The EPA hazardous waste generator guidance and your local regulations explain how shops should handle this kind of waste.

Choosing a Cleaning Solution for the STW-500
Spray wash cabinets like the STW-500 use water-based detergents made for heated spray washers. These detergents are designed to work at high temperatures and to produce little foam. Foam is a problem in a spray cabinet because it can cause the pump to lose suction and can overflow the tank.
Choose a detergent that matches the metals you clean. Some products are safe for steel and cast iron but can stain or etch aluminum. If you clean a lot of aluminum heads, transmission cases, or intake manifolds, use a detergent labeled as safe for aluminum. Follow the detergent maker’s mixing ratio and keep the solution in the 135°F-175°F range the heater provides.
Check the safety data sheet for any detergent you use, and make sure employees know how to handle it. The OSHA hazard communication standard covers labeling, safety data sheets, and training for chemicals used in the workplace.

Step-by-Step: Running a Wash Cycle in the STW-500
- Fill the tank with water to the correct level and add the recommended amount of detergent.
- Turn on the heater and let the solution reach working temperature, between 135°F and 175°F.
- Scrape off heavy, caked-on grease and dirt so it does not clog the nozzles or filters.
- Place heavy parts in the center of the turntable to keep the load balanced.
- Hang smaller parts on the tree rack and put loose hardware in the parts basket.
- Check that nothing touches the nozzle pipes or the cabinet walls when the turntable turns.
- Close and latch the door.
- Set the 60-minute timer for the cycle length you need and start the STW-500.
- When the cycle ends and the machine shuts off, wait a few minutes for steam to clear before opening the door.
- Wear gloves and eye protection, remove the parts, and rinse or dry them as needed.
Many parts come out clean in a shorter cycle. Heavily soiled engine blocks and transmission cases may need the full 60 minutes. With some practice, your technicians will learn the right cycle time for each type of part.
Maintenance Tips for a Long Service Life
Simple routine care keeps the STW-500 cleaning well and protects the pump and heater. Here are the main tasks:
- Skim oil often. Let the included oil skimmer do its job and empty the collected oil regularly.
- Check the solution level. Water evaporates when it is heated. Top off the tank so the heater element always stays covered.
- Clean the nozzles. Remove and clear any nozzle that becomes blocked so the spray pattern stays even.
- Remove sludge. Dirt and metal particles settle in the bottom of the tank. Clean out sludge on a regular schedule.
- Change the solution. When the detergent stops cleaning well, drain the tank, dispose of the waste properly, and refill with fresh solution.
- Inspect the turntable. Make sure it turns freely and that nothing is stuck under it.
- Look at the door seal. A good seal keeps spray and steam inside the cabinet.
The STW-500 comes with a 1-year limited parts warranty. Keeping a simple maintenance log helps you spot problems early and shows a clear history of care if you ever need a warranty part.

Benefits of the STW-500 Over Hand Washing
Many shops still clean parts by hand in a solvent tank with a brush. That method works, but it takes a lot of technician time, and it exposes workers to solvent fumes and skin contact. An automatic spray cabinet like the STW-500 changes the process in several ways:
- Labor savings. A technician loads the cabinet and walks away. The STW-500 does the scrubbing while the technician does billable work.
- Consistent results. Heated solution at 43 GPM reaches every side of the part as the turntable spins, so parts come out evenly clean.
- Bigger loads. A 1,000-lb. turntable handles heavy blocks and a full set of parts at once.
- Water-based cleaning. Using detergent and hot water instead of solvent can reduce fumes in the shop.
- Better inspections. Clean parts make it easier to find cracks, wear, and damage before reassembly.
Who Should Buy the Atlas STW-500?
The STW-500 is a good fit for:
- General automotive repair shops that clean engine and transmission parts often
- Engine rebuilders and machine shops that prepare blocks and heads for machining
- Transmission shops that need clean cases and housings
- Fleet maintenance departments servicing cars, vans, and light trucks
- Restoration shops cleaning old, greasy parts before refinishing
- Small engine, motorcycle, and powersports repair shops
If your shop cleans parts several times a day, the time saved by the STW-500 adds up fast. If you mostly work on heavy-duty trucks with very tall transmissions and diesel blocks, compare the 42-inch inside height with your parts first.

STW-500 Safety Guidelines
Hot water, chemicals, and heavy parts call for basic safety habits around any spray washer:
- Wear chemical-resistant gloves and safety glasses when handling parts and solution.
- Let steam clear before opening the door after a cycle.
- Use a hoist or engine crane to lift heavy blocks onto the turntable.
- Never exceed the 1,000-lb. turntable capacity.
- Keep the electrical connection dry and have a qualified electrician handle any wiring.
- Train every employee who uses the STW-500 on its controls and safety steps.

Pairing the STW-500 With Other Shop Equipment
A parts washer works best as part of an organized workflow. Many shops place the STW-500 near the engine stand area or teardown bench so dirty parts travel a short distance. An engine crane or overhead hoist makes loading heavy blocks safer and faster. After cleaning, parts can go straight to inspection, machining, or reassembly.
If your shop is growing, you may also be looking at car lifts and other bay equipment. Planning the floor layout with the wash cabinet, lifts, and benches in mind helps you avoid moving heavy equipment twice.
Frequently Asked Questions About the STW-500
What is the tank capacity of the STW-500?
The STW-500 has a 50-gallon tank for water and cleaning solution.
How much weight can the STW-500 turntable hold?
The 30-inch turntable is rated for up to 1,000 lbs.
What are the inside dimensions of the STW-500?
The wash chamber is 42 inches high and 32 inches wide.
What power does the STW-500 need?
It needs 220 volt, single phase power with a 30 amp breaker.
How hot does the STW-500 heat the solution?
The heater element heats the solution to between 135°F and 175°F.
How long is a cycle?
The STW-500 has a 60-minute timer with automatic shut-off, so you can choose a shorter cycle or run the full hour.
How many nozzles does it have?
It has 19 adjustable steel nozzles fed by a 43 GPM pump at 28 PSI.
What comes with the STW-500?
The cabinet includes an oil skimmer, a tree rack, and a parts basket.
What is the shipping weight?
The STW-500 ships at 750 lbs. and is sent freight prepaid.
What warranty comes with the STW-500?
Atlas covers the cabinet with a 1-year limited parts-only warranty.
Order the Atlas STW-500 Today
The Atlas STW-500 spray wash cabinet gives your shop a heated, automatic way to clean heavy parts with less labor. With a 1,000-lb. turntable, a 50-gallon tank, 19 adjustable nozzles, a 43 GPM pump, and a 60-minute timer with automatic shut-off, the STW-500 is built for daily use in busy repair and rebuild shops. Contact Ironside Garage with questions about sizing, power, or delivery, and browse our full range of shop equipment to finish outfitting your service bays.
Related products
Atlas SBC1200 X-Large Sandblast Cabinet
Atlas SBC1200 X-Large Sandblast Cabinet with Dual Doors & Vacuum The Atlas SBC1200 sandblast cabinet takes many of the already great features of the Atlas® SBC990 blasting cabinet and doubles them. The SBC1200 sandblast cabinet has two, front and rear, extra large top open loading doors and features
BendPak Bender
BendPak Bender heavy-duty “Blue-Bullet” exhaust pipe bender. This high-quality bender takes off like a shot and helps you reach your production target every time. Your purchase of the BB-2 comes complete with a die package and a dual-function end-finishing unit for precision OE expansions and flares

Reviews
There are no reviews yet.