Mahle ATJ 1000H Shop PRO Automotive Transmission Jack 1000 lbs

$3,057.00

Mahle ATJ 1000H Shop PRO Automotive Transmission Jack 1000 lbs

SKU: IRG0540 Categories: ,
Description

The Mahle ATJ 1000H ShopPRO is a 1,000 lb. automotive transmission jack built for use under a vehicle on a lift. Its two-stage design raises fast on air and fine-tunes with hydraulics, reaching 72 inches of lift height. With tilt adjustment in three directions and a quick-securing Speed-Strap, the ATJ 1000H makes transmission removal and installation safer and faster.

Mahle ATJ 1000H Shop PRO Automotive Transmission Jack 1000 lbs

FEATURES

Two-stage design: 1st stage 100% air operated for speed; 2nd stage hydraulic for precise control

Swivel casters make for easy maneuverability

Nylon Speed-Strap™ quickly and conveniently secures the load

Heavy-duty acme threaded screws provide greater bearing surface for easier tilt adjustments

Additional adapters available

Product Specifications

Capacity 1,000 lb (454 kg)

Minimum Start Height 34.5 in (88 cm)

Maximum Lift Height 72 in (183 cm)

Power 1st Stage Air / 2nd Stage Hydraulic

Head Plate Dimensions 11.5 in x 11.5 in (29 cm x 29 cm)

Dimensions (W x L) 41 in x 41 in (104 cm x 104 cm)

Swivel Caster Diameter 4 in (10 cm)

Required Air Pressure 90 to 160 psi (6.2 to 11.0 bar)

Tilt (Forward / Rear / Side to Side) 40° / 20° / 10°

Shipping 125 lb (57 kg)

ATJ 1000H Specifications

  • Capacity: 1,000 lbs.
  • Minimum start height: 34.5 inches
  • Maximum lift height: 72 inches
  • Power: first stage air, second stage hydraulic
  • Head plate: 11.5 x 11.5 inches
  • Base dimensions (W x L): 41 x 41 inches
  • Swivel casters: 4-inch diameter
  • Required air pressure: 90 to 160 psi
  • Tilt: 40° forward, 20° rear, 10° side to side
  • Shipping weight: 125 lbs.

Two-Stage Lifting: Speed and Control

The ATJ 1000H uses a smart two-stage system. The first stage is fully air operated, so the saddle rises quickly toward the transmission without endless pumping. The second stage switches to hydraulics for slow, precise movement when you’re lining up bellhousing bolts or mating the transmission to the engine. You get the speed you want for the big moves and the control you need for the final inch.

Tilt Adjustment in Three Directions

Transmissions rarely sit perfectly level. The ATJ 1000H lets you tilt the head plate 40° forward, 20° back, and 10° side to side. Heavy-duty Acme threaded screws give a larger bearing surface, so tilt adjustments are smoother and easier, even under load. Precise tilt control makes alignment far less frustrating.

Secure the Load Quickly

A nylon Speed-Strap secures the transmission to the head plate fast. Wrap it, tighten it, and you’re ready to lower the unit away from the vehicle. A secure load is essential when moving a heavy component overhead.

Easy to Maneuver

Four 4-inch swivel casters let you roll the ATJ 1000H under the vehicle and position it accurately. The wide 41 x 41-inch base adds stability while you work.

Designed for Use With a Lift

With a minimum start height of 34.5 inches and a maximum of 72 inches, the ATJ 1000H is built for vehicles raised on a two-post or four-post lift. It meets the transmission at working height, so technicians can stand comfortably while removing and installing.

Who Should Buy the ATJ 1000H

  • Auto repair shops doing transmission and clutch work
  • Transmission specialists
  • Fleet maintenance departments
  • Serious home mechanics with a full-height lift
  • Technical schools and training centers

Browse related equipment in our shop equipment section.

How to Use the ATJ 1000H

  1. Raise the vehicle on a lift to a comfortable working height and lock it.
  2. Connect the jack to an air supply between 90 and 160 psi.
  3. Roll the ATJ 1000H under the transmission and center the head plate.
  4. Use the air stage to raise the saddle quickly toward the transmission.
  5. Switch to the hydraulic stage for fine contact and adjust tilt to match the transmission angle.
  6. Secure the transmission with the Speed-Strap.
  7. Remove mounts and bolts per the service manual, then lower the transmission slowly and roll it clear.

Installation is the reverse: raise the transmission close with air, then use hydraulics and tilt adjustments to align it precisely with the engine.

Safety Guidelines

Never exceed the ATJ 1000H’s 1,000 lb. capacity. Always secure the load with the Speed-Strap before lowering or moving. Keep the load centered on the head plate, move slowly when the transmission is raised, and keep people clear of the area under the load. Use the jack only on a hard, level floor, and follow Mahle’s operating instructions.

ATJ 1000H key specifications

Why a Dedicated Transmission Jack Matters

Trying to remove a transmission with a floor jack or by hand is risky. Transmissions are heavy, awkward, and top-heavy, and they need to come straight off the engine without tipping. A dedicated transmission jack like the ATJ 1000H supports the unit on a wide head plate, lets you tilt it to match the mounting angle, and holds it securely while you work. That means less strain, fewer damaged parts, and a safer shop.

Jobs the ATJ 1000H Helps With

  • Automatic and manual transmission removal and installation
  • Clutch replacement
  • Transfer case service
  • Rear main seal replacement
  • Flywheel and flexplate work
  • Supporting other drivetrain components during service

Air Supply Tips

The ATJ 1000H needs 90 to 160 psi of air for the first stage. Make sure your compressor can supply that pressure and that hoses and fittings are in good condition. Drain moisture from the compressor tank regularly to keep air tools and the jack working smoothly.

ATJ 1000H

Maintenance Tips

  • Inspect the Speed-Strap for cuts, fraying, or wear.
  • Check hydraulic fluid level and look for leaks.
  • Keep Acme screws clean and lightly lubricated for smooth tilt adjustment.
  • Check casters for smooth rolling and secure mounting.
  • Inspect air fittings and hoses for leaks.

ATJ 1000H vs. Low-Profile Transmission Jacks

Low-profile transmission jacks are designed for vehicles on jack stands or low lifts. The ATJ 1000H, with its 34.5- to 72-inch range, is built for vehicles on full-height lifts. If your shop uses two-post or four-post lifts, a high-lift jack like the ATJ 1000H lets technicians stand while they work, which is safer and more comfortable.

Getting the Tilt Right

Alignment is the hardest part of installing a transmission. The input shaft must slide straight into the clutch or torque converter, and the bellhousing must sit flush against the engine. The ATJ 1000H’s three-way tilt makes this much easier. Start by matching the forward or rearward angle of the engine, then fine-tune side to side. Use the hydraulic stage to raise or lower in small steps until the dowel pins line up. With patience and the right adjustments, the transmission slides home without force.

Speed in a Busy Shop

Every minute counts in a professional shop. The air-powered first stage gets the head plate to the transmission quickly, and the Speed-Strap secures the load in seconds. Swivel casters make positioning under the vehicle simple. Together, these features help technicians finish transmission and clutch jobs faster, which can improve shop productivity and profitability.

Built for Professional Use

Mahle’s ShopPRO line is designed for daily shop use. The ATJ 1000H combines a sturdy base, durable casters, heavy-duty Acme screws, and a reliable two-stage lifting system. With basic care, it’s built to handle years of transmission and drivetrain work.

Additional Adapters

Mahle offers additional adapters for the ATJ 1000H, which can help when working with specific transmissions or drivetrain components. Ask our team which adapters suit the vehicles you service most often.

ATJ 1000H tilt and control

Training Technicians

Make sure every technician who uses the ATJ 1000H understands the two-stage controls, tilt adjustments, and strap securing before using it on a job. A short walkthrough with an empty jack helps build confidence and good habits. Post key safety steps near the jack’s storage spot.

Storage and Care

Store the ATJ 1000H on a level floor in a clean, dry area when it’s not in use. Lower the head plate fully to protect the lifting mechanism and keep the strap coiled neatly. Wipe off transmission fluid and grime after each job so the jack stays in good shape and the head plate surface stays clean for the next job.

A Typical Clutch Job With the ATJ 1000H

Clutch replacement is one of the most common reasons shops reach for a transmission jack. With the vehicle on a lift, the technician disconnects the driveshaft or axles, linkage, wiring, and crossmember. The ATJ 1000H rolls into place, rises quickly on air, and then uses hydraulics to make gentle contact with the transmission.

The Speed-Strap goes on, the bellhousing bolts come out, and the transmission slides back and down, supported the whole way. After the new clutch is installed, the jack brings the transmission back up, and the tilt controls help line up the input shaft with the clutch disc. The result is a smoother, safer job with less physical strain.

Why Technicians Prefer Two-Stage Jacks

Single-stage hydraulic jacks can be slow to raise, especially when starting at the bottom of their range. Air-only jacks can be quick but less precise. The ATJ 1000H combines both, giving technicians fast travel and precise control in one tool. Many technicians find that this combination reduces the time spent on positioning and makes alignment far more predictable.

Stability Matters

A transmission perched on a jack high in the air needs a stable base. The ATJ 1000H’s 41 x 41-inch footprint spreads the load and resists tipping. Combined with the low, wide stance and swivel casters, it gives technicians confidence when maneuvering under a vehicle. Always keep the floor clear of tools and debris so the casters roll smoothly.

Pairing With the Right Lift

The ATJ 1000H works best with a lift that raises the vehicle to a comfortable standing height. Two-post lifts are common choices for transmission work because they leave the underside fully open. Four-post lifts with rolling jacks can also work well. If you’re outfitting a new bay, our team can help you choose a lift and transmission jack that work together.

ATJ 1000H front view

Choosing a Transmission Jack Capacity

Transmission weights vary widely. Many passenger car and light truck transmissions fall well within the 1,000 lb. capacity of the ATJ 1000H, but heavy-duty and commercial transmissions can weigh more. Before lifting, check the weight of the transmission you’re removing, including the torque converter and any attached components like transfer cases. If you regularly work on heavy commercial vehicles, consider a higher-capacity commercial jack. For most automotive and light truck shops, the ATJ 1000H offers the right balance of capacity, speed, and control.

Shop Safety Practices

  • Clear the floor around the lift before rolling the jack under the vehicle.
  • Communicate with team members before lowering a transmission.
  • Keep hands and feet away from the base and casters while moving a load.
  • Never leave a loaded jack unattended in a raised position.
  • Lower the load to the minimum practical height before rolling the jack.
  • Inspect the jack before each use and remove it from service if anything looks wrong.

Investing in the Right Tools

Quality equipment pays for itself in a professional shop. A dependable transmission jack reduces the risk of injury, protects expensive components from damage, and helps technicians finish jobs faster. The ATJ 1000H is a solid investment for shops that want reliable performance on transmission and clutch work every day.

ATJ 1000H best uses

What Technicians Appreciate

Technicians often point to the fast air stage and the precise hydraulic stage as the standout features. They also like the generous tilt range, which makes stubborn alignments easier, and the quick Speed-Strap that saves time on every job. For many shops, the ATJ 1000H quickly becomes the go-to tool for drivetrain work.

Removing an Automatic Transmission

Automatic transmissions add the torque converter to the job, which must stay seated as the transmission is removed. With the ATJ 1000H, technicians can support the transmission at the right angle and move it straight back from the engine, keeping the converter in place. Many technicians use a converter holding strap or bracket during removal. Once the transmission is clear of the engine, lower it slowly with the hydraulic stage, keeping the load level, and roll it out from under the vehicle. On reinstallation, the tilt controls help line up the converter and the dowels so the transmission seats evenly before any bolts are tightened.

Working Efficiently on Repeat Jobs

Shops that perform frequent transmission or clutch work benefit from setting up a consistent routine. Keep the ATJ 1000H stored near the lift bays, keep the air hose ready, and have adapters organized. Train technicians to use the same steps every time. That consistency makes each job faster and safer.

Getting Started

If you’re adding transmission work to your shop or replacing an older jack, the ATJ 1000H is a practical choice. Contact our team to confirm it suits your lifts and the vehicles you service, and we’ll help you get it delivered and ready for work.

Why Mahle ShopPRO Equipment

Mahle is a global name in automotive components and service equipment. The ShopPRO line brings that experience to everyday shop tools, with designs focused on safety, efficiency, and durability. The ATJ 1000H reflects those priorities with a two-stage lift, a precise tilt system, a stable base, and a quick-securing strap. It’s a tool designed by people who understand what technicians need when they’re working under a vehicle with a heavy component overhead.

Comfort and Ergonomics

Transmission work can be physically demanding. Reaching overhead, supporting weight, and making fine adjustments all take a toll over a full day. Because the ATJ 1000H meets the transmission at working height and does the heavy lifting, technicians can focus on alignment and fasteners instead of fighting the load. Smooth tilt screws and an easy-rolling base reduce effort even more. Better ergonomics mean less fatigue, fewer injuries, and more consistent work quality.

From quick clutch jobs to full transmission swaps, the ATJ 1000H brings speed, precision, and confidence to every drivetrain job in your shop.

Have questions about capacity, adapters, or air requirements? Our team is happy to help you confirm that the ATJ 1000H is the right transmission jack for your shop before you order.

For shops that value speed, precision, and safety on every drivetrain job, the ATJ 1000H is a dependable choice that technicians quickly come to rely on.

Frequently Asked Questions About the ATJ 1000H

What is the capacity?

The ATJ 1000H is rated for 1,000 lbs.

What height range does it cover?

From 34.5 inches minimum to 72 inches maximum.

How is it powered?

The first stage is air operated and the second stage is hydraulic.

How much air pressure does it need?

90 to 160 psi.

How much can it tilt?

40° forward, 20° rear, and 10° side to side.

What size is the head plate?

11.5 x 11.5 inches.

Support From Ironside Garage

Our team can help you choose the right transmission jack for your lifts and the vehicles you service. Contact us with any questions about the ATJ 1000H.

Order the ATJ 1000H Today

The Mahle ATJ 1000H ShopPRO is a proven, powerful transmission jack for professional shops. Learn more about the manufacturer on the Mahle Aftermarket website, or explore our car lifts to pair with it.

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “Mahle ATJ 1000H Shop PRO Automotive Transmission Jack 1000 lbs”

Your email address will not be published. Required fields are marked *

Shipping & Delivery