Mahle CFL-4A 4 Ton Forklift Jack Air Assist
$2,544.00
Mahle CFL-4A 4 Ton Forklift Jack Air Assist ShopPRO heavy-duty forklift jacks have set the industry standard for forklift jacks for over 40 years and feature a two position lift pad that easily adjusts to handle flat-edged surfaces.
The Mahle CFL-4A is a 4-ton air assist forklift jack that uses shop air to lift forklifts and other low-clearance equipment quickly. It has an 8,000-lb. capacity, a low 2 1/4-inch starting height, and a maximum lift height of 16 inches. The air/hydraulic system runs on 155 psi, so technicians can raise heavy loads without pumping by hand. A two-position lift pad handles flat or edged surfaces, and the Hold-to-Run release knob gives a slow, controlled descent.
This guide covers the CFL-4A specifications, how it works, where to use it, safe lifting, maintenance, and common questions. If you service forklifts and want faster, easier lifting from your shop equipment, the Mahle CFL-4A is a smart upgrade.
Mahle CFL-4A 4 Ton Forklift Jack Air Assist
FEATURES
Two position lift pad that easily adjusts to handle flat or edged surfaces
Low starting height of 2 1/4″ allows maximum flexibility
Hold-to-Run™ release knob provides a slow descent rate with precise operator control
Product Specifications
Capacity 8,000 lb (3,629 kg)
Maximum Lift Height 16 in (41 cm)
Power Air/Hydraulic
Required Air Pressure 155 psi (10.7 bar)
Reach (Raised Position) 7 in (18 cm)
(Distance from Hydraulic Cylinder to Lift Pad)
Width 8 in (20 cm)
Starting Pad Height (Lift Arm Noch) 2.3 in (5.8 cm)
Starting Pad Height (Serrated Lift Pad) 2.5 in (6.3 cm)
Shipping Weight 68 lb (31 kg)
Mahle CFL-4A Specifications
- Capacity: 8,000 lbs. (3,629 kg), or 4 tons
- Maximum lift height: 16 inches (41 cm)
- Power: air/hydraulic
- Required air pressure: 155 psi (10.7 bar)
- Reach (raised position): 7 inches (18 cm), measured from the hydraulic cylinder to the lift pad
- Width: 8 inches (20 cm)
- Starting pad height (lift arm notch): 2.3 inches (5.8 cm)
- Starting pad height (serrated lift pad): 2.5 inches (6.3 cm)
- Low starting height: 2 1/4 inches
- Shipping weight: 68 lbs. (31 kg)
What Is a Forklift Jack?
A forklift jack is a hydraulic jack designed to lift forklifts and similar equipment that sit very low to the ground. Standard floor jacks often cannot fit under a forklift frame or counterweight, and bottle jacks may start too high. A forklift jack like the CFL-4A uses a lift arm that starts close to the floor and reaches out from the hydraulic cylinder, so it can slide under low points and raise heavy loads.
Technicians use forklift jacks to raise one corner or one end of a forklift so they can change tires, service brakes, inspect the mast and steering axle, or work on the drive train. The jack lifts the equipment just enough to do the job, and then the load is supported on proper stands or blocking.
Key Features of the CFL-4A
8,000-lb. Capacity
The CFL-4A is rated for 8,000 lbs., or 4 tons. That capacity covers lifting one end or corner of many forklifts and pieces of industrial equipment. Always know the weight on the lift point and stay within the rated capacity.
Low 2 1/4-Inch Starting Height
The CFL-4A starts at just 2 1/4 inches. The lift arm notch sits at 2.3 inches, and the serrated lift pad sits at 2.5 inches. This low profile lets the jack slide under equipment with very little ground clearance, giving you maximum flexibility to find a safe lift point.
Two-Position Lift Pad
The lift pad has two positions that adjust to handle flat or edged surfaces. Use the lift arm notch to catch an edge, such as a frame lip or the bottom of a counterweight. Use the serrated lift pad for flat surfaces, where the serrations help grip the load and keep it from slipping.
Hold-to-Run Release Knob
The Hold-to-Run release knob gives a slow descent rate with precise operator control. The load comes down only while the operator holds the knob. Let go, and lowering stops. This design helps the operator lower heavy equipment gently onto stands or the ground.
16-Inch Maximum Lift Height
The CFL-4A lifts up to 16 inches. That is plenty of height to raise a forklift wheel clear of the ground for tire changes and to give room for service under the machine.
Compact and Portable
With a width of 8 inches and a shipping weight of 68 lbs., the CFL-4A is compact enough to carry to equipment in a warehouse, yard, or service bay.
How the CFL-4A Works
The CFL-4A is an air/hydraulic jack with air assist. Compressed shop air at 155 psi powers the pump, which forces hydraulic fluid into the cylinder and pushes the ram up. The ram raises the lift arm, and the lift pad at the end of the arm lifts the load. Because air assist does the pumping, a technician can lift thousands of pounds quickly without working a handle by hand.
The lift arm reaches 7 inches out from the hydraulic cylinder in the raised position. This reach lets the cylinder stay clear of the equipment while the pad sits under the lift point. To lower the load, the operator turns and holds the Hold-to-Run release knob, which lets fluid flow back slowly and lowers the arm at a controlled rate.
Common Uses for the CFL-4A
- Raising forklifts to change solid or pneumatic tires
- Lifting one end of a forklift for brake and steering axle service
- Inspecting the underside of material handling equipment
- Raising pallet jacks, floor scrubbers, and industrial carts
- Lifting machinery for leveling or installing pads and casters
- Raising low-clearance equipment in rental yards and warehouses
Forklift service departments, warehouse maintenance teams, equipment rental companies, and industrial plants all find uses for a forklift jack. Because the CFL-4A is portable, it can go to the equipment instead of the equipment coming to the shop.

Choosing the Right Lift Point
Lifting a forklift safely starts with choosing the right lift point. Check the forklift manufacturer’s service manual for approved jacking points. These are areas of the frame designed to carry the weight of the machine. Avoid lifting on sheet metal, hoses, the mast, or other parts that are not built to support the load. Use the lift arm notch when the lift point has an edge, and use the serrated lift pad when the lift point is flat. Make sure the pad is fully seated before lifting.
If the pad sits only partly on the lift point, stop and reposition the jack. Remember that a forklift’s weight is not evenly spread. The counterweight end is much heavier than the fork end. Know the weight on the corner or end you plan to lift and make sure it stays within the CFL-4A’s 8,000-lb. capacity.
Step-by-Step: Lifting a Forklift With the CFL-4A
- Park the forklift on a hard, level surface. Lower the forks fully to the ground.
- Set the parking brake, turn off the engine or power, and remove the key.
- Chock the wheels that will stay on the ground.
- Find the approved jacking point in the forklift service manual.
- Choose the lift arm notch for an edge or the serrated pad for a flat surface.
- Slide the CFL-4A under the lift point and make sure the pad is fully seated.
- Connect the air supply and use the air assist to raise the load slowly. Watch the jack and the forklift as it rises.
- Lift only as high as needed for the job, up to the 16-inch maximum.
- Place rated jack stands or cribbing under the forklift at a solid support point.
- Use the Hold-to-Run release knob to lower the load gently onto the stands.
- Never work under a load supported only by a jack.
When the job is finished, raise the load just enough to remove the stands, then hold the release knob to lower the forklift slowly to the ground.
Safety Tips for Using a Forklift Jack
- Never exceed the 8,000-lb. rated capacity.
- Always use the jack on a hard, level surface.
- Use jack stands or cribbing to support the load before working under it.
- Keep hands and feet clear of the lift pad and load while lifting and lowering.
- Lower the load slowly using the Hold-to-Run knob.
- Inspect the jack before each use for leaks, damage, or worn parts.
- Disconnect the air supply before servicing the jack.
- Do not use a damaged or leaking jack.
- Train every operator on safe jacking procedures.
OSHA’s powered industrial trucks resources cover forklift safety, including maintenance practices that keep equipment and workers safe.
CFL-4A Maintenance Tips
- Check hydraulic fluid. Keep the fluid at the level shown in the owner’s manual and use the recommended type.
- Look for leaks. Inspect seals and fittings for oil leaks before each use.
- Keep it clean. Wipe off dirt and debris, especially around the ram and lift arm.
- Lubricate pivot points. Follow the manual for lubrication of moving parts.
- Inspect the lift pad. Check the serrations and notch for wear or damage.
- Use clean, dry air. Drain compressor tanks and use a water separator to keep moisture out of the air system.
- Store it properly. Store the jack with the arm lowered in a clean, dry place.
Routine inspections help catch problems early and keep the CFL-4A ready for safe lifting.
CFL-4A vs. Standard Floor Jacks
A standard floor jack is great for cars and light trucks, but it often struggles with forklifts. Many floor jacks have a starting height that is too tall to fit under a forklift frame. Their long chassis can also be hard to position around wheels and counterweights. And many car jacks are not rated for the heavy concentrated loads a forklift places on a single lift point. The CFL-4A is built for this kind of work.
Its 2 1/4-inch starting height slides under low points, its 7-inch reach lets the cylinder stay clear of the machine, and its two-position pad handles both edges and flat surfaces. With an 8,000-lb. capacity in a compact 8-inch-wide body, it is made for forklift and equipment lifting. 

CFL-4A vs. Bottle Jacks
Bottle jacks are strong and compact, but their starting height is usually too high for forklifts. They also lift straight up from the base, so the jack must fit directly under the lift point. The CFL-4A’s lift arm reaches out from the cylinder and starts close to the floor, which makes it easier to position under low equipment.
Who Should Buy the Mahle CFL-4A?
- Forklift dealers and service departments
- Warehouse and distribution center maintenance teams
- Equipment rental companies
- Manufacturing plants with material handling fleets
- Mobile forklift service technicians
- Facility maintenance crews that move and level machinery
If your team regularly services forklifts or other low-clearance equipment, the CFL-4A gives you a dedicated tool that makes lifting faster and safer.
Building a Forklift Service Area
A forklift service area works best with the right tools close at hand. Along with the CFL-4A, many shops keep rated jack stands, wheel chocks, cribbing blocks, tire tools, and a parts washer nearby. Good lighting and a clean, level floor make every job safer. If your shop also services cars and trucks, our car lifts can help round out your service bays.
Understanding the Two Starting Heights
Mahle lists two starting pad heights for the CFL-4A because of its two-position lift pad. In the lift arm notch position, the starting height is 2.3 inches (5.8 cm). With the serrated lift pad, the starting height is 2.5 inches (6.3 cm). The overall low starting height is listed as 2 1/4 inches.
Choose the position based on the lift point. If the equipment has very little clearance and an edge to catch, the notch gives you the lowest start. If the lift point is flat and you need a better grip, the serrated pad is the better choice. Being able to switch between the two lets one jack handle many different machines.
Getting the Most From Your CFL-4A
Keep the CFL-4A in a dedicated spot so it is always easy to find and stays protected from damage. Train technicians on the right lift points for each forklift model in your fleet, and keep the service manuals handy. Post a simple checklist near the jack with the key safety steps: level ground, chocks, correct lift point, stands before working under the load, and slow lowering with the Hold-to-Run knob. Inspect the jack on a regular schedule and keep a log of checks and any service. A well-kept jack lasts longer and gives your team confidence every time they lift.

Forklift Tire Changes With the CFL-4A
Tire changes are one of the most common reasons to lift a forklift. Solid and pneumatic forklift tires wear down with daily use, and worn tires can affect stability and handling. To change a tire, the wheel must be raised clear of the floor so it can be removed.
With its low starting height and 16-inch lift, the CFL-4A can raise a forklift wheel off the ground at an approved jacking point. Once the wheel is raised, place stands or cribbing under the frame before removing lug nuts and the wheel. After the new tire is mounted and the wheel is reinstalled, raise the forklift slightly to remove the supports, then lower it slowly with the Hold-to-Run knob.
Using the CFL-4A for Equipment Leveling
Forklift jacks are useful for more than forklifts. Maintenance teams often need to raise heavy machines a few inches to install leveling pads, add shims, place rollers, or slide equipment onto dollies. The CFL-4A’s low lift arm can get under machine bases and skids that sit close to the floor. When lifting machinery, find a solid lift point on the frame or base, keep the load within 8,000 lbs., and lift evenly. For large machines, lift one side at a time in small steps and support each side with blocking as you go. Never place any part of your body under a raised machine.
Why Portability Matters
Forklifts break down where they work, not always in the shop. A heavy service jack can be hard to bring to a forklift stuck in a warehouse aisle or out in a yard. At 68 lbs. and only 8 inches wide, the CFL-4A can be carried or carted to the machine, so technicians can make repairs on site and get equipment back to work faster.
Air Assist vs. Manual Forklift Jacks
Mahle offers the CFL-4 manual hydraulic forklift jack and the CFL-4A air assist model with the same 8,000-lb. capacity, 16-inch lift, and 2 1/4-inch starting height. The difference is how the jack is powered. The manual model is pumped by hand. The CFL-4A uses 155 psi shop air to drive the hydraulics, so lifting is faster and takes less effort. In a busy forklift shop where technicians lift equipment many times a day, air assist reduces fatigue and speeds up every job. If you work where shop air is always available, the CFL-4A is the more productive choice.
Frequently Asked Questions About the CFL-4A
What is the capacity of the CFL-4A?
The CFL-4A is rated for 8,000 lbs. (3,629 kg), or 4 tons.
How high does it lift?
The maximum lift height is 16 inches (41 cm).
What is the starting height?
The low starting height is 2 1/4 inches. The lift arm notch starts at 2.3 inches and the serrated lift pad at 2.5 inches.
What is the reach of the lift arm?
In the raised position, the reach is 7 inches (18 cm) from the hydraulic cylinder to the lift pad.
How is the CFL-4A powered?
It is an air/hydraulic jack with air assist that requires 155 psi (10.7 bar).
How does the release work?
The Hold-to-Run release knob provides a slow descent rate with precise operator control.
How wide is the jack?
The CFL-4A is 8 inches (20 cm) wide.
How much does it weigh?
The shipping weight is 68 lbs. (31 kg).
Can I work under a forklift held only by the jack?
No. Always support the load with rated jack stands or cribbing before working under it.
Order the Mahle CFL-4A Forklift Jack Today
The Mahle CFL-4A 4-ton forklift jack gives your team an 8,000-lb. capacity, a low 2 1/4-inch starting height, a two-position lift pad, and controlled lowering with the Hold-to-Run release knob. It is compact, portable, and built for forklift and equipment service. Contact Ironside Garage with questions, and browse our full range of shop equipment.
Related products
Atlas SBC990 Large Sandblast Cabinet with Vacuum
Atlas SBC990 Large Sandblast Cabinet with Vacuum The Atlas SBC990 sandblast cabinet has many of the same features of the entry level Atlas® SBC420 blasting cabinet with added interior space and an extra large front/top loading door. That extra work space and larger opening allow the user to blast ev
BendPak Bender
BendPak Bender heavy-duty “Blue-Bullet” exhaust pipe bender. This high-quality bender takes off like a shot and helps you reach your production target every time. Your purchase of the BB-2 comes complete with a die package and a dual-function end-finishing unit for precision OE expansions and flares
Cool Boss CB-28L Portable Evaporative Air Cooler
Cool Boss CB-28L Portable Evaporative Air Cooler The CB-28 is a medium-duty commercial-grade cooler that is well-suited for large industrial space cooling. When temperatures rise and you’re looking for a cost-effective cooling solution, look no further than Cool Boss. The CB-28 evaporative cooler pu

Reviews
There are no reviews yet.