Bendpak VMP-10120V-603 V-Max Elite Air Compressor
$6,095.00
Bendpak VMP-10120V-603 V-Max Elite Air Compressor All Craft, No Compromise: The V-Max Elite 10120V-603 This V-Max Elite air compressor is a top-of-the-line air delivery system designed for maximum efficiency under every load condition. Like others in the V-Max Elite series of air compressors, the 10
The BendPak VMP-10120V-603 V-Max Elite is a 10 HP, 120-gallon vertical air compressor built for big air demand in busy shops. Its two-stage, V-4 solid cast-iron pump delivers 26 CFM at 175 PSI on a continuous duty cycle, while turning at just 625 RPM for quieter operation. It runs on 208-230V, 3-phase power with a magnetic starter, and it is UL, CSA, and ASME certified. Dual drive belts, an inter-cooler and after-cooler, an electronic drain valve, and anti-vibration pads round out a compressor designed for reliability and low cost of ownership.
This guide covers the VMP-10120V-603 specifications, how it works, sizing, installation, maintenance, and common questions. If you need a high-capacity air supply for your shop equipment, the V-Max Elite is built for it.
Bendpak VMP-10120V-603 V-Max Elite Air Compressor
V-Max air compressor pump
This massive V-Max pump comes standard with splash lubrication and a V-4 finned cylinder configuration for 360° cooling. Heavy-duty, disc-type valves have been engineered for absolute reliability, and users can even access them without having to perform complicated valve maintenance procedures or remove the cylinder. A built‐in intercooler and air‐cooled after-cooler chills the air to bring down the temperatures and keep condensation to a minimum. Still, at its heart, the V-Max Elite 10120V-603 air compressor is all about big air with comparably little noise due to slower RPM speeds and a two-stage design.
Anti-vibration pads
This air compressor includes a set of four rugged, half-inch thick pads to ensure there’s virtually zero machine vibration during operation. The high-quality elastomer compound resists aging, compression set, water and oil.
Cooling fan
All V-Max Elite air compressors run at noticeably slower speeds, thanks to their massive, energy-efficient pumps. We do this to reduce operating temperatures and maintenance costs while increasing overall efficiency. When making an air compressor purchase, it’s always a good idea to consider the power it consumes along with the general upkeep you’ll have to perform to keep it running. The true cost of ownership is more than the purchase price.
Electric power costs add up based on the horsepower needed to produce the air required. The more air you can produce per horsepower, the less power is required to meet your air demands. When you stack what the V-Max 10120V-603 can achieve next to the other guys, it isn’t hard to see that no one can touch the value of a V-Max Elite air compressor by BendPak.
SPECIFICATIONS
10 HP energy-efficient motor
Extra-quiet, low-RPM pump
Cast-iron V-Max Elite pump features simple splash lubrication for total reliability and a “V-4” finned cylinder configuration that provides 360° cooling
Proven air-cooled design is economical, reliable and environmentally friendly
Two compression rings and one oil control ring provide excellent oil control and high efficiency air delivery
Dual drive belts require less belt tension resulting in less load on pump bearings, longer belt life and low vibration
Fully-enclosed belt guard
Cast-iron pump and heads are more stable under heavy workloads and do not warp from heat like aluminum cylinders with a pressed-in sleeves do
ASME rated tank
Large surface area and cooling fins on cylinders and forced-air after-cooler provides efficient heat dissipation for lower operating temperatures and dryer air. Compressor runs cooler, oil life is extended and maintenance is reduced
Tapered roller main bearings provide full contact and support of the crankshaft and needle-type piston pin bearings properly distribute bearing loads
Precision balanced flywheel has forced-air fan blades for optimum compressor cooling and life
Magnetic starter provides thermal overload protection and minimizes start loads providing long life and trouble‐free operation
ASME rated safety valve protects the VMP-10120V-603 from overpressure and safeguards the operator
Balanced flywheel and counterbalanced crankshaft results in nearly vibration-free operation
Readily accessible disc-valves do not require disassembly of compressor piping, for easy accessibility and reduced maintenance cost and downtime
Corrosion resistant tubing for coolers, separators and valves for longer life and reduced maintenance
Oversized ductile iron crankshaft provides extra strength and longer wear
High-density, die-cast aluminum alloy rods minimize reciprocating weight
Rugged cast iron oil reservoir has convenient sight gauge glass, large oil drain and convenient fill cap
Automatic pressure switch provides auto start and stop
Integrated pressure unloader valves are built into the intake valve assembly on the VMP-10120V-603 head, reducing internal pump heat from initial start-up compression
Pressure gauge with service valve
Oversize replaceable air filters
Motor
Pump
Tank
Dimensions
Shipping
BendPak VMP-10120V-603 Specifications
Motor
- Horsepower: 10 HP
- Motor RPM: 1,750
- Voltage: 208-230V AC, 3-phase, 60 Hz
- Magnetic starter: yes
- Amp draw: 18 amps
- Recommended breaker: 50 amp
- Noise: 78 dB
Pump
- Style: two-stage, V-4
- Pump RPM: 625
- Material: solid cast iron
- Duty cycle: continuous
- Air delivery: 26 CFM rated at 175 PSI
- Maximum pressure: 175 PSI
- Drive: belt drive, dual belts
- Lubrication: oil lubricated, with oil sight glass
Tank
- Orientation: vertical
- Size: 120 gallons
- Outlet: 3/4″ fitting
- Electronic drain valve: yes
- Certifications: UL, CSA, ASME
Shipping
- Shipping weight: 880 lbs. (399 kg)
- Shipping dimensions: 45″ x 40″ x 78″ (1,143 mm x 1,016 mm x 1,981 mm)
How a Two-Stage Compressor Works
A two-stage compressor squeezes air in two steps. In the first stage, a larger piston compresses outside air to a middle pressure. The air then passes through an inter-cooler, which removes some of the heat created by compression. In the second stage, a smaller piston compresses the cooled air to the final pressure, up to 175 PSI on the VMP-10120V-603.
Compressing in two stages is more efficient than trying to reach high pressure in a single step. Cooling the air between stages means the pump runs cooler and works less hard. After the second stage, the VMP-10120V-603’s air-cooled after-cooler chills the air again before it enters the tank. Cooler air holds less moisture, so less water condenses in your air lines and tools.
Why 26 CFM at 175 PSI Matters
CFM, or cubic feet per minute, tells you how much air a compressor delivers. PSI tells you the pressure. The VMP-10120V-603 delivers 26 CFM rated at 175 PSI. Many air tools are rated at 90 PSI, and a compressor that delivers strong CFM at high pressure has plenty of reserve for tools running at lower pressure.
High maximum pressure also matters for the 120-gallon tank. At 175 PSI, the tank stores more air than it would at a lower pressure, so the VMP-10120V-603 cycles less often and tools have a larger reserve to draw from during heavy use.
Key Features of the VMP-10120V-603
Solid Cast-Iron Pump
The VMP-10120V-603’s pump and heads are solid cast iron. Cast iron is more stable under heavy workloads and does not warp from heat like aluminum cylinders with pressed-in sleeves. Two compression rings and one oil control ring provide excellent oil control and efficient air delivery.
Continuous Duty Cycle
The pump is rated for a continuous duty cycle, which means it is built to handle long run times in a busy shop.
Low-RPM, Extra-Quiet Pump
The pump turns at just 625 RPM. Low pump speed reduces wear and noise, and the VMP-10120V-603 runs at 78 dB.
Dual Drive Belts
Two drive belts share the load, so each needs less tension. That means less load on the pump bearings, longer belt life, and less vibration. A fully enclosed belt guard covers the belts and pulleys.
Inter-Cooler and After-Cooler
A built-in inter-cooler and an air-cooled after-cooler chill the air, reducing heat and condensation moisture. Large cooling fins on the cylinders and a forced-air fan on the flywheel help the VMP-10120V-603 run cooler, which extends oil life and reduces maintenance.
Accessible Disc-Type Valves
Heavy-duty disc-type valves are dependable and can be reached without removing the cylinder head or disassembling compressor piping. That reduces maintenance time and cost.
Strong Rotating Assembly
An oversized ductile iron crankshaft adds strength and wear life. Tapered roller main bearings support the crankshaft, needle-type piston pin bearings distribute loads, and high-density die-cast aluminum alloy rods reduce reciprocating weight. A balanced flywheel and counterbalanced crankshaft keep vibration low.
Pressure Switch and Unloader Valves
An automatic pressure switch starts and stops the VMP-10120V-603 as needed, so no energy is wasted. Integrated unloader valves in the intake valve assembly reduce pump heat from start-up compression.
ASME Safety Valve
An ASME-rated safety valve protects the VMP-10120V-603 from over-pressure and safeguards the operator.
Electronic Drain Valve
An electronic drain valve automatically drains condensation from the tank, helping prevent rust and keeping moisture out of your air lines.
Anti-Vibration Pads Included
Four rugged, half-inch-thick elastomer pads reduce vibration. The pads resist aging, compression set, water, and oil.
Cast-Iron Oil Reservoir
The rugged cast-iron oil reservoir has a sight glass, a large oil drain, and a convenient fill cap, making oil checks and changes simple.
Certified
The VMP-10120V-603 is UL, CSA, and ASME certified.

What Can the VMP-10120V-603 Power?
With 26 CFM at 175 PSI and a 120-gallon tank, the VMP-10120V-603 is built to run a busy automotive shop. Common uses include:
- Impact wrenches and air ratchets
- Tire changers and wheel balancers
- Air-over-hydraulic jacks and lift locks
- Air sanders, grinders, and cut-off tools
- Paint guns and blow guns
- Fluid exchangers and other air-powered shop equipment
Check the CFM rating of each tool and add up the tools you expect to run at the same time. Leave some extra capacity so the compressor is not running at its limit all day.
Sizing a Compressor for Your Shop
Choosing the right compressor comes down to how much air you use and how often. A small home garage may only need a little air for occasional tool use. A professional shop with several technicians running impact guns, tire machines, and sanders needs much more. The VMP-10120V-603’s two-stage pump, continuous duty rating, and 120-gallon tank make it suited for steady professional use.
Think about future growth too. If you plan to add bays, lifts, or tire equipment, choosing a compressor with extra capacity now can save you from upgrading later.
Installation and Power Requirements
The VMP-10120V-603 runs on 208-230V AC, 3-phase, 60 Hz power. It draws 18 amps, and BendPak recommends a 50-amp breaker. A magnetic starter is included. Have a licensed electrician install the circuit and make the connection to meet local electrical codes.
Place the compressor on a solid, level concrete floor in a clean, dry, well-ventilated area. Use the included anti-vibration pads. Leave space around the compressor for airflow and service access. Good airflow helps the pump stay cool, and cooler air coming in means drier air going out.
Connect the 3/4-inch tank outlet to your shop air system with properly rated piping. Install a shutoff valve, a filter, and a water separator or dryer for best results. Plan drops near each bay so technicians have easy access to air.
The shipping weight is 880 lbs., so plan for a forklift or pallet jack at delivery and an easy path to the final location.
Understanding the Lifetime Cost
The price on the tag is only part of what a compressor costs. Electricity, oil, belts, filters, and repairs all add up over the years. A compressor that runs cooler and more efficiently can cost less to own over its life. The VMP-10120V-603’s low-RPM cast-iron pump, inter-cooler, after-cooler, and efficient 10 HP motor are designed to keep operating costs and wear down.


VMP-10120V-603 Maintenance Tips
- Check the oil daily using the sight glass, and change it on the schedule in the owner’s manual.
- Inspect the air filter and replace the oversize filter when it gets dirty.
- Check the belts for wear and proper tension.
- Confirm the electronic drain valve is working so condensation leaves the tank.
- Test the safety valve as the manual recommends.
- Keep cooling fins clean so the pump can shed heat.
- Check for air leaks in fittings and lines.
Routine care keeps the VMP-10120V-603 running cool and efficient and helps it deliver many years of service.
Compressed Air Safety
- Never exceed the tool or hose pressure ratings.
- Wear eye protection when using air tools and blow guns.
- Do not point compressed air at people or use it to clean skin or clothing.
- Shut off and drain pressure before servicing the compressor or air lines.
- Keep the belt guard in place at all times.
- Have all electrical work done by a qualified electrician.
OSHA’s hand and power tools resources cover safe use of pneumatic tools and compressed air in the workplace.
Saving Energy With Compressed Air
Compressed air is one of the most expensive forms of energy in a shop. Leaks, oversized pressure settings, and running the compressor when no one is working all waste power. Fix leaks quickly, set pressure only as high as your tools need, and turn the compressor off at the end of the day. The U.S. Department of Energy’s compressed air resources offer more tips for efficient systems.
Who Should Buy the BendPak VMP-10120V-603?
- Automotive repair shops
- Tire and wheel service centers
- Collision and body shops
- Fleet maintenance garages
- Fabrication and welding shops
- Serious hobbyists with large home garages

Setting Up a Shop Air System
A good compressor works best with a well-planned air system. Run main lines sized for the flow you need, slope them slightly so water drains toward drop legs, and install drains at low points. Add a filter, regulator, and lubricator where tools need them. A refrigerated air dryer can remove even more moisture for paint work. With the VMP-10120V-603’s after-cooler and electronic drain valve doing their part, a clean, dry air system protects your tools and gives better results.
Before you order, confirm that your building has 208-230V 3-phase power and room for a 50-amp breaker, and choose a clean, ventilated spot for the compressor. A little planning makes installation quick.
Why Choose 3-Phase Power?
Many commercial buildings have 3-phase electrical service. A 3-phase motor like the 10 HP motor on the VMP-10120V-603 starts smoothly and runs efficiently, and its 18-amp draw is modest for a compressor this size. The included magnetic starter provides thermal overload protection and reduces start loads for long, trouble-free operation. If your building does not have 3-phase power, talk with an electrician before ordering.
Frequently Asked Questions About the VMP-10120V-603
How much air does the VMP-10120V-603 deliver?
It delivers 26 CFM rated at 175 PSI.
What is the maximum pressure?
The maximum pressure is 175 PSI.
How big is the tank?
The vertical tank holds 120 gallons.
What power does it need?
It runs on 208-230V AC, 3-phase, 60 Hz, draws 18 amps, and BendPak recommends a 50-amp breaker.
How loud is it?
The VMP-10120V-603 runs at 78 dB.
Is it rated for continuous duty?
Yes. The pump has a continuous duty cycle.
What kind of pump does it have?
It has a two-stage, V-4, solid cast-iron pump that runs at 625 RPM.
Does it have an automatic drain?
Yes. It has an electronic drain valve.
Is it certified?
Yes. It is UL, CSA, and ASME certified.
What is the shipping weight?
The shipping weight is 880 lbs. (399 kg).
Order the BendPak VMP-10120V-603 Today
The BendPak VMP-10120V-603 10 HP, 120-gallon two-stage air compressor gives your shop 26 CFM at 175 PSI, a continuous-duty cast-iron pump, quiet 78 dB operation, and a long list of features built for reliability. Contact Ironside Garage with questions about power or installation, and browse our full range of shop equipment.
Related products
Atlas SBC990 Large Sandblast Cabinet with Vacuum
Atlas SBC990 Large Sandblast Cabinet with Vacuum The Atlas SBC990 sandblast cabinet has many of the same features of the entry level Atlas® SBC420 blasting cabinet with added interior space and an extra large front/top loading door. That extra work space and larger opening allow the user to blast ev
Flo-Dynamics PROMAX40 Heavy Duty ATF Inline Exchanger
Mahle CSP-75 75 Ton Shop Press
Mahle FluidPRO ATX 280 Transmission Fluid Exchange System with Adapters
Mahle FluidPRO ATX-3 and Boost Transmission Fluid Exchange System
Mahle FluidPRO ATX-3 and Boost Transmission Fluid Exchange System FluidPRO equipment from MAHLE Service Solutions offers a range of choices in fluid exchange equipment. The ATX+Boost offers technicians fully-automatic operation with precise fluid measurement to maximize efficiency. The added feature
Portacool Apex 1200 Wi-Fi Enabled High Velocity Portable Evaporative Cooler for 1200 sq ft
Portacool Apex 1200 Wi-Fi Enabled High Velocity Portable Evaporative Cooler for 1200 sq ft Meet the Portacool APEX™ 1200—a game-changer for mid-sized spaces demanding serious cooling. Delivering a powerful 4,000 CFMs of airflow that spans up to 40 ft., this unit ensures consistent comfort across 1,2
Ranger RS-750DS
Ranger RS-750DS The incredible RS-750DS is made out of rust-free stainless-steel and has a 1,000 lb. weight capacity that can hold some of the biggest car, truck, and SUV parts on the market. This stainless steel 53-gallon capacity spray wash cabinet can rapidly degrease dirty parts, including large

Reviews
There are no reviews yet.