QuickJack Package (1) 5000TLX-110V + (1) Wall Hangers Set + (1) Pinch Weld Blocks Set

$2,050.00

We at QuickJack developed the 5000TLX simply because the 5000TL had a limiting lift point of 60”. That works for most vehicles, but then there are those vehicles out there whose manufacturer-recommended lift points are just an inch or two out of reach. While that may sound like an insignificant diff

SKU: IRG0347 Categories: ,
Description

The QuickJack 5000TLX Package is a complete kit for longer cars. It includes the 110V QuickJack 5000TLX extended-length portable lift, a wall hangers set, and a urethane pinch-weld blocks set. The 5000TLX Package reaches lift points from 43 to 66 inches apart, lifts up to 5,000 lbs., protects unibody seams, and stores neatly on the wall.

Wall Hangers Set

There are a lot of ways to stow your QuickJack in a garage: you can lean them against a wall; stack them on top of each other; tuck them together under your vehicle, etc. The opportunities for easy and convenient. They’re practically endless. While some people prefer to hang their frames on the wall, up and out of the way. These convenient wall hangers are the best way to make that happen.

If you’d like to hang your portable car lift frames on the wall of your garage, QuickJack’s exclusive hangers will mount directly into a sturdy wall stud for safe, simple storage. It is recommended that the hangers are installed at the same height while also being high enough that the frames will rest on the floor. This will make it much easier to lift and hang the frames onto the hooks of the wall hangers.

Pinch Weld Blocks Set

Supporting cars on pinch-weld rails creates excessive pressure points which can end up gouging or tearing the standard rubber blocks. You could also end up inadvertently damaging delicate body rails on unibody vehicles. QuickJack’s urethane rubber pinch-weld blocks were engineered with a cross-cut slotted design, which allows you to position them lengthwise or crosswise. They’re the perfect body cradling tool to safely support rocker panels or sheet metal body rails, especially pinch-weld rails which have been degraded over time due to corrosion from grime and road salt.

You’ll be able to ensure a long lifespan for your lift blocks with QuickJack’s specially designed pinch-weld jack pads. You can place these taller-than-average blocks independently in the lift block trays. Not only that, but they can be stacked without placing a pinch-weld block on top of a small standard block. (The pinch-weld and tall standard blocks should not be stacked.) Ditch the wooden blocks, hockey pucks, and the towels which can slip or tear easily, resulting in vehicle damage, or worse, unstable lifting. The durable urethane rubber is impermeable to oil, grease, and gas. It will also be able to last for years and years of simple, maintenance-free lifting.

Features

5000TLX

  • Automatic Safety Locks
  • Increased Lifting Height
  • One-Handed Operation
  • Accessories to Increase Versatility

Wall Hangers

  • Sold in sets of two
  • NEW! Now in powder-coated black!
  • One size fits all QuickJack models
  • Over-engineered to 150% rated capacity
  • Solid-steel construction
  • Sleek, laser-cut QuickJack logo design
  • Designed and engineered by QuickJack

Pinch-Weld Blocks

  • Specially formulated urethane rubber
  • Bilateral deep slots accommodate virtually all pinch weld frames
  • Position lengthwise or crosswise
  • Water/Chemical resistant and 100% weatherproof
  • Single-piece construction for superior hold
  • Sold in sets of 4

Specifications

Lifting Capacity

Capacity 5,000 lbs. (2,268 kg)

Lowered Height

A – Frame only: 3″ (76 mm)
B – With 2″ block: 3.5″ (89 mm)

Lifting Height

D – With 2″ block: 21″ (521 mm)
E – With 3″ block: 22″ (546 mm)
F – Max. height: 24″ (616 mm)
G – With adapters: 24″ (597 mm)
H – With adapters + pin: 26.75″ (673 mm)

Lift Point Spread

I – Maximum: 60″ (1,524 mm)
J – Minimum: 37″ (940 mm)

Frame dimensions (ea.)

K – Width: 11″ (278 mm)
L – Length: 70″ (1,778 mm)
A – Height: 3″ (76 mm)
Weight: 78 lbs. (35 kg)

Other Spec

Power/Voltage 110V, 60HZ, 1PH
Time to full rise: 30 seconds
Power unit weight: 30 lbs. (13 kg)
Shipping Dimensions (ea. Frame): 73.5″ (L) x 15.25″ (W) x 5″ (H) (1,869 mm x 385 mm x 129 mm)
Shipping weight: 318 lbs. (144 kg)

Wall Hangers

A – Width: 4.75″ (121 mm)
B – Height: 6.75″ (172 mm)
C – Depth: 2.25″ (57 mm)
Weight (ea.): 1 lbs. (0.5 kg)
Shipping weight: 3 lbs. (1.4 kg)

Pinch-Weld Blocks

A – Length: 4″ (102 mm)
B – Width: 3″ (76 mm)
C – Height of puck: 3″ (76 mm)
D – Pinch-weld width: 0.4″ (10 mm)
E – Pinch-weld depth: 0.5″ (13 mm)

Click here for Setup and Operation Manual

Inside the 5000TLX Package

  • QuickJack 5000TLX (110V) – 5,000 lb. capacity, 76-inch frames, 43 to 66 inch lift point spread, up to 24 inches of lift, 3-inch lowered height
  • Wall hangers set – mounts into a sturdy wall stud to hold the frames vertically
  • Pinch-weld blocks set – urethane blocks with a cross-cut slot for unibody pinch-weld rails

5000TLX Package extended frames

Why Choose the Extended 5000TLX?

The 5000TLX has frames that are 6 inches longer than the standard 5000TL, and its lift point spread shifts from 37–60 inches to 43–66 inches. That makes the 5000TLX Package the better choice for cars with longer wheelbases, such as full-size sedans, wagons, grand tourers, and some crossovers. With the right frame length, you can put the blocks exactly where your manufacturer recommends.

The lift reaches full rise in about 30 seconds, uses dual-position automatic safety locks, and runs on standard 110V power. Each frame weighs 81.5 lbs., so the lift is still easy to move and store.

Protecting Pinch Welds on Longer Cars

Many longer sedans and wagons are unibody vehicles with pinch-weld lift points. Flat rubber blocks can concentrate pressure on those thin seams, which can tear the blocks or bend the rail. The urethane pinch-weld blocks in the 5000TLX Package have a cross-cut slot that holds the seam while the block supports the body around it. Turn the blocks lengthwise or crosswise to match each lift point.

Storage Made Simple

Long frames take up floor space, so storage matters even more with an extended lift. The wall hangers in the 5000TLX Package mount into a sturdy stud and hold each frame upright. Install both hangers at the same height, high enough to hold the frames while letting them rest on the floor. That way, you tip each frame onto its hook instead of lifting the full weight overhead.

5000TLX Package features

Who Should Buy the 5000TLX Package

  • Owners of long-wheelbase sedans, wagons, and grand tourers
  • Owners whose lift points are too far apart for the standard 5000TL
  • Unibody car owners who want to protect pinch welds
  • Home mechanics who want an organized garage
  • First-time lift buyers who want a complete package

Need a different size or capacity? Explore our portable car lifts.

Setting Up the 5000TLX Package

  1. Find a sturdy wall stud near your lifting spot and mount both hangers at the same height.
  2. Assemble the 5000TLX and prepare the power unit according to the manual.
  3. Park on a flat, level, hard surface and set the parking brake.
  4. Slide each 76-inch frame under the car from the side.
  5. Fit the pinch-weld blocks and line up each slot with the seam.
  6. Raise a few inches, check every block, then lift fully so the locks engage.

Safety Reminders

Never exceed 5,000 lbs. Always rest the car on the automatic locks before working underneath. Keep others clear while lifting, chock the wheels when working at one end, and inspect hoses and blocks before every lift. Follow the QuickJack operating manual at all times.

5000TLX Package certified lift

Jobs You Can Do With the 5000TLX Package

  • Brake pads, rotors, and calipers
  • Tire rotations and seasonal swaps
  • Oil and filter changes
  • Suspension and alignment prep
  • Exhaust work
  • Detailing lower panels and wheel wells

Where to Use It

Use the 5000TLX Package on smooth, level concrete or firm asphalt. Avoid gravel, dirt, grass, and slopes. Because the frames are 76 inches long, leave room to slide them in from the side, and keep the area well lit.

5000TLX Package Maintenance

  • Check hoses and fittings for leaks.
  • Keep couplers clean and capped.
  • Check the power unit’s fluid level.
  • Clean the urethane blocks after use.
  • Hang the frames on the wall to keep them dry and out of the way.

5000TLX Package frames

Measuring Your Car First

Before you order, find your car’s front and rear lift points on one side and measure the distance between them. If it’s between 43 and 66 inches, the 5000TLX Package should reach both. If it’s shorter than 43 inches, the standard 5000TL package may fit better. Also confirm your car’s curb weight is within 5,000 lbs., keeping in mind passengers and cargo should be removed before lifting.

Package Value

Most owners of extended lifts eventually add wall storage and pinch-weld protection. The 5000TLX Package includes both from the beginning, so you don’t need separate orders later. Every part is designed to work together, and you’re ready to lift on day one.

5000TLX Package vs. Jack and Stands

On a long car, getting a jack to the right lift point and placing four stands can be awkward. A floor jack’s flat saddle can also crush pinch welds. The 5000TLX Package reaches the right points with its longer frames, cradles the seams in slotted blocks, lifts a whole side at once, and holds the car on automatic locks. It’s faster and kinder to your car.

5000TLX Package

5000TLX Package vs. a Post Lift

Post lifts need high ceilings, a strong slab, and permanent floor space. The 5000TLX Package works on any level floor, hangs on the wall when not in use, and moves with you. For tires, brakes, oil changes, and inspections, it offers plenty of height and access.

A Typical Brake Job

Take the frames off the hangers and slide them under the car. Fit the pinch-weld blocks so each seam sits in its slot. Raise the car a few inches, check every block, then lift fully so the locks engage. Pull all four wheels, inspect pads and rotors, and replace parts as needed. Reinstall and torque the wheels, lower the car, and hang the frames back up. With everything in one kit, the job flows smoothly from start to finish.

5000TLX Package lift

Taking the 5000TLX Package to the Track

The 5000TLX frames weigh 81.5 lbs. each and the power unit is light, so the lift can travel to track days and car events. Bring the pinch-weld blocks along in a small bag, plug into a 110V outlet, and you have a pit lift for longer cars wherever you go.

5000TLX Package Owner Tips

  • Mount the hangers close to your lifting spot.
  • Mark frame positions on the floor for quick setup.
  • Keep the lift point page from your manual in the garage.
  • Store blocks, hoses, and the pendant together.
  • Check that each seam sits in its slot before lifting higher.

Cars That Fit the 5000TLX Package Well

The 5000TLX Package is a natural match for full-size sedans, station wagons, grand touring coupes, long-roof hatchbacks, and some crossovers that weigh 5,000 lbs. or less. These vehicles often have lift points spaced too far apart for standard-length frames. The extended 5000TLX closes that gap, and the pinch-weld blocks protect the unibody seams most of these cars use. Always check your manual for lift point locations and weight before lifting.

Choosing Block Heights

Besides the pinch-weld blocks, the 5000TLX comes with standard rubber blocks in 2-inch and 3-inch heights. With the 2-inch blocks, the lift reaches about 21 inches; with the 3-inch blocks, about 22 inches. The frame’s maximum height is 24 inches, and adapters with the pin reach 26.75 inches. Use the pinch-weld blocks on seams and the standard blocks on flat lift pads or frame points, depending on your vehicle.

A Cleaner, Safer Garage

Frames left on the floor are easy to trip over and can get scratched or dirty. With the wall hangers in the 5000TLX Package, your frames stay upright and protected. The pinch-weld blocks, power unit, and hoses can live on a nearby shelf. When it’s time to work, everything is in one spot. When you’re done, it all goes back in a few minutes, leaving your garage clean and safe.

Built for the Long Run

The 5000TLX’s steel frames, sturdy wall hangers, and weatherproof, oil-resistant urethane blocks are built for regular use. Inspect hoses before each lift, keep couplers clean, check fluid levels, and clean the blocks after use. With that simple care, your 5000TLX Package will serve you well for years of maintenance and projects.

Your First Lift

Start with a tire rotation to get familiar with the setup. Measure, place the frames, fit the pinch-weld blocks, and raise the car slowly while checking each seam. Once the car is on the locks, you’ll see how much easier under-car work becomes. After a few lifts, the whole process takes just minutes.

Why a Complete Kit Saves Hassle

When you buy a lift on its own, it’s easy to overlook the small things that make daily use better. Many new owners discover after a few lifts that their pinch welds need protection, or that frames on the floor are always in the way. The 5000TLX Package solves both problems up front. You get storage, unibody protection, and an extended-length lift in one shipment, so your first lift is also your best-prepared lift.

That preparation pays off every time you work on your car. You spend less time hunting for parts, less time setting up, and more time actually getting the job done. For busy owners who want to maintain their own cars without turning every job into a project, that convenience is worth a lot.

What Owners Appreciate

Owners of longer cars often say the 5000TLX Package finally gave them a portable lift that truly fits. They appreciate how the extended frames reach the right lift points, how the slotted blocks protect the seams, and how quickly the frames hang back on the wall. Add one-handed pendant control, automatic locks, and a 30-second lift, and it’s easy to see why this kit is a favorite among enthusiasts with longer vehicles.

Whether you’re rotating tires on a Saturday morning or tackling a full brake job, the 5000TLX Package makes the work easier, safer, and more enjoyable from start to finish.

For owners of longer cars who want a portable lift that fits properly, protects the body, and stores out of the way, the 5000TLX Package brings all of those benefits together in one practical kit that is ready to use from the day it arrives in your garage.

Questions about whether your car fits? Send us its make, model, and year, and our team will gladly help you check lift point spacing, weight, and the best accessories before you order.

Frequently Asked Questions About the 5000TLX Package

What’s included?

One 110V QuickJack 5000TLX lift, one wall hangers set, and one pinch-weld blocks set.

What’s the lift point spread?

43 to 66 inches.

What’s the capacity?

5,000 lbs.

How fast does it lift?

About 30 seconds to full rise.

Can I use it on a standard-length car?

If your lift points are at least 43 inches apart, yes. Shorter spacing may suit the 5000TL better.

Support From Ironside Garage

Our team can help you choose between the TL and TLX packages, confirm fit, and plan delivery. Contact us with any questions.

Order the 5000TLX Package Today

The 5000TLX Package is a proven, powerful, complete lifting kit for longer cars. Learn more on the official QuickJack website, or explore our full car lifts collection.

Reviews (0)

Reviews

There are no reviews yet.

Be the first to review “QuickJack Package (1) 5000TLX-110V + (1) Wall Hangers Set + (1) Pinch Weld Blocks Set”

Your email address will not be published. Required fields are marked *

Shipping & Delivery